Cisco Systems 6000 manual TCP Probe, FTP, SMTP, and Telnet Probe, DNS Probe Submode

Page 50

Configuring Probes for Health Monitoring

TCP Probe

A TCP probe establishes and removes connections. The ip slb probe tcp command enters the TCP probe configuration mode. All the common ip slb probe commands are supported.

 

Command

Purpose

Step 1

 

 

Router(config)# ip slb probe probe-nametcp

Configure a TCP probe and enter the TCP probe

 

 

submode1.

Step 2

Router(config-slb-probe-tcp)# [expect

Configure the intervals to wait between probes of a

 

failed interval open receive

failed server and between probes. Also, specify the

 

retries]

time to make a TCP connection, to receive a reply

 

 

 

 

from the server, and to limit the number of retries

 

 

before considering the real server as failed.

 

 

 

1.The no form of this command restores the defaults.

FTP, SMTP, and Telnet Probe

An FTP, SMTP, or Telnet probe establishes a connection to the real server and verifies that a greeting from the application was received. The ip slb probe (ftp, smtp, or telnet) command enters the corresponding probe configuration mode. All the ip slb probe common options are supported. Multiple status ranges are supported, one command at a time.

To configure a status code to expect from the FTP, SMTP, or Telnet probe, perform this task:

 

Command

Purpose

Step 1

 

 

Router(config)# ip slb probe probe-name[ftp

Configure an FTP, SMTP, or Telnet probe and enter

 

smtp telnet]

the FTP, SMTP, or Telnet probe submode1.

Step 2

 

 

Router(config-slb-probe-ftp)# [expect status

Configure the intervals to wait between probes of a

 

min-number [max-number] failed interval

failed server and between probes. Also, specify the

 

retries receive]

time to make a TCP connection, to receive a reply

 

 

 

 

from the server, and to limit the number of retries

 

 

before considering the real server as failed.

 

 

 

1.The no form of this command restores the defaults.

DNS Probe Submode

A DNS probe sends a domain name resolve request to the real server and verifies the returned IP address. The ip slb probe dns command places the user in DNS probe configuration submode. All the ip slb probe common options are supported except open, which is ignored.

 

Catalyst 6000 Family Content Switching Module Installation and Configuration Note

50

78-11631-02 Rev. A0

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Contents Overview These sections describe the CSM FeaturesDescribes the features of the CSM Status LED CSM front panel features are shown in FigureFront Panel Description Off Red Orange Green Green to Orange Operation ModeRJ-45 Connector Content Switching Module and Servers Client-to-Content Switching Module-to-Server Traffic Flow Client-to-CSM-to-Server Traffic FlowSafety Overview Memory Requirements CSM memory is not configurableSystem Requirements Environmental Requirements Power RequirementsHardware Supported 72-876-01 Console Cable Not applicableRequired Tools Installing the Content Switching ModulePreparing to Install the CSM Software RequirementsInstalling the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the InstallationUpgrading to a New Software Release Using the Command-Line InterfaceAccessing Online Help CSM upgrade 127.0.0.zz c6slb-apc.revision-num.bin Upgrading from the Supervisor Engine BootflashSet up a session between the supervisor engine and the CSM Routerconfig# power cycle module slot-numberRouter config# power cycle module slot-number Routerconfig# tftp-server slotxc6slb-apc.revision-num.binCSM upgrade slot0 c6slb-apc.revision-num.bin Upgrading from a Pcmcia CardSwitchport access vlan Configuring the Content Switching ModuleSwitchport Router# vlan databaseConfiguration Overview Configuring VLANs Configure the required parameters in the following sectionsConfiguring VLANs See for the following notesConfiguring Client-Side VLANs Configuring Server-Side VLANsConfiguring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies into a cookie map Configure multiple cookiesConfiguring Sticky Groups Configuring Virtual Servers Configuring TCP Parameters Configuring Dynamic Feedback ProtocolConfiguring Redirect Virtual Servers Configuring Client NAT Pools Writing and Restoring Configurations Configuring Server NATConfiguration Examples Single Subnet Bridge Mode ConfigurationConfigure a server-side Vlan Enter the Vlan modeConfigure a client-side Vlan Exit to have the configuration take effectCreate the client-side Vlan 2 and enter the SLB Secure Router Mode ConfigurationVlan mode Create the server-side Vlan 3 and enter the SLB Fault-Tolerant ConfigurationRouterconfig# ip slb vlan 3 server Exit the submodeRouterconfig# int GigabitEthernet 2/1 Router# configure terminalRouterconfig# mac access-list extended Venus Routerconfig-if#service-policy input VenusFault-tolerant configuration, the following rules apply Configuration Parameter On Both Content Switching ModulesRouter B Hsrp address Create the client-side Vlan 2 and enter the SLB Vlan modeAssign the Content Switching IP address on 192.158.38.10Create the Content Switching primary Assign the default route for VlanDefine Vlan 9 as a fault-tolerant Vlan Configure a client-side VLAN2Configuring Hsrp Hsrp Configuration OverviewConfigure Switch 2-FT2 Hsrp secondary as follows CSG VlanConfiguring CSM VLANs Configure VLANs on Hsrp FT2 as followsAdd ports to the EtherChannel as follows Configuring Probes for Health MonitoringConfigure EtherChannel on both switches as follows Icmp creates an Icmp probe with a default configuration Probe-name is the name of the probe being configured it hasHttp creates an Http probe with a default configuration Telnet creates a Telnet probe with a default configurationCommands Available to all Probe Configurations Http ProbeIcmp Probe DNS Probe Submode TCP ProbeFTP, SMTP, and Telnet Probe RHI Overview Configuring Route Health InjectionUnderstanding RHI Routing to VIP Addresses Without RHI Routing to VIP Addresses With RHIUnderstanding How the CSM Determines VIP Availability Configuring RHI for Virtual ServersRouterconfig# ip slb vserver vserver1 Understanding Propagation of VIP Availability InformationRegulatory Standards Compliance Translated Safety WarningsSafety Information Referral Warning Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Release Notes for Catalyst 6000 Family IOS Software Related DocumentationQualified Personnel Warning Documentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationObtaining Technical Assistance Contacting TAC by Using the Cisco TAC WebsiteTo access Cisco.com, go to the following website Cisco.comContacting TAC by Telephone Obtaining Technical Assistance
Top Page Image Contents