Cisco Systems 6000 manual Related Documentation, Qualified Personnel Warning

Page 58

Related Documentation

Qualified Personnel Warning

Warning Only trained and qualified personnel should be allowed to install or replace this equipment.

Waarschuwing Installatie en reparaties mogen uitsluitend door getraind en bevoegd personeel uitgevoerd worden.

Varoitus Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai vaihtaa tämän laitteen.

Avertissement Tout installation ou remplacement de l'appareil doit être réalisé par du personnel qualifié et compétent.

Achtung Gerät nur von geschultem, qualifiziertem Personal installieren oder auswechseln lassen.

Avvertenza Solo personale addestrato e qualificato deve essere autorizzato ad installare o sostituire questo apparecchio.

Advarsel Kun kvalifisert personell med riktig opplæring bør montere eller bytte ut dette utstyret.

Aviso Este equipamento deverá ser instalado ou substituído apenas por pessoal devidamente treinado e qualificado.

¡Atención! Estos equipos deben ser instalados y reemplazados exclusivamente por personal técnico adecuadamente preparado y capacitado.

Varning Denna utrustning ska endast installeras och bytas ut av utbildad och kvalificerad personal.

Related Documentation

For more detailed installation and configuration information, refer to the following publications:

•Site Preparation and Safety Guide

•Catalyst 6000 Family Installation Guide

•Catalyst 6000 Family Quick Software Configuration Guide

•Catalyst 6000 Family Module Installation Guide

•Catalyst 6000 Family IOS Software Configuration Guide

•Catalyst 6000 Family IOS Command Reference

•ATM Software Configuration and Command Reference—Catalyst 5000 Family and Catalyst 6000 Family Switches

•Catalyst 6000 Family IOS System Message Guide

•For information about MIBs, refer to: http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

•Release Notes for Catalyst 6000 Family IOS Software

	Catalyst 6000 Family Content Switching Module Installation and Configuration Note
58	78-11631-02 Rev. A0

Image 58

Contents Contents Overview Describes the features of the CSM FeaturesThese sections describe the CSM Front Panel Description CSM front panel features are shown in FigureStatus LED RJ-45 Connector Operation ModeOff Red Orange Green Green to Orange Content Switching Module and Servers Client-to-Content Switching Module-to-Server Traffic Flow Client-to-CSM-to-Server Traffic FlowSafety Overview System Requirements CSM memory is not configurableMemory Requirements Environmental Requirements Power RequirementsHardware Supported 72-876-01 Console Cable Not applicableRequired Tools Installing the Content Switching ModulePreparing to Install the CSM Software RequirementsInstalling the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the InstallationAccessing Online Help Using the Command-Line InterfaceUpgrading to a New Software Release CSM upgrade 127.0.0.zz c6slb-apc.revision-num.bin Upgrading from the Supervisor Engine BootflashSet up a session between the supervisor engine and the CSM Routerconfig# power cycle module slot-numberRouter config# power cycle module slot-number Routerconfig# tftp-server slotxc6slb-apc.revision-num.binCSM upgrade slot0 c6slb-apc.revision-num.bin Upgrading from a Pcmcia CardSwitchport access vlan Configuring the Content Switching ModuleSwitchport Router# vlan databaseConfiguration Overview Configuring VLANs Configure the required parameters in the following sectionsConfiguring VLANs See for the following notesConfiguring Client-Side VLANs Configuring Server-Side VLANsConfiguring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies into a cookie map Configure multiple cookiesConfiguring Sticky Groups Configuring Virtual Servers Configuring TCP Parameters Configuring Dynamic Feedback ProtocolConfiguring Redirect Virtual Servers Configuring Client NAT Pools Writing and Restoring Configurations Configuring Server NATConfiguration Examples Single Subnet Bridge Mode ConfigurationConfigure a server-side Vlan Enter the Vlan modeConfigure a client-side Vlan Exit to have the configuration take effectVlan mode Secure Router Mode ConfigurationCreate the client-side Vlan 2 and enter the SLB Create the server-side Vlan 3 and enter the SLB Fault-Tolerant ConfigurationRouterconfig# ip slb vlan 3 server Exit the submodeRouterconfig# int GigabitEthernet 2/1 Router# configure terminalRouterconfig# mac access-list extended Venus Routerconfig-if#service-policy input VenusFault-tolerant configuration, the following rules apply Configuration Parameter On Both Content Switching ModulesRouter B Hsrp address Create the client-side Vlan 2 and enter the SLB Vlan modeAssign the Content Switching IP address on 192.158.38.10Create the Content Switching primary Assign the default route for VlanDefine Vlan 9 as a fault-tolerant Vlan Configure a client-side VLAN2Configuring Hsrp Hsrp Configuration OverviewConfigure Switch 2-FT2 Hsrp secondary as follows CSG VlanConfiguring CSM VLANs Configure VLANs on Hsrp FT2 as followsConfigure EtherChannel on both switches as follows Configuring Probes for Health MonitoringAdd ports to the EtherChannel as follows Icmp creates an Icmp probe with a default configuration Probe-name is the name of the probe being configured it hasHttp creates an Http probe with a default configuration Telnet creates a Telnet probe with a default configurationCommands Available to all Probe Configurations Http ProbeIcmp Probe FTP, SMTP, and Telnet Probe TCP ProbeDNS Probe Submode Understanding RHI Configuring Route Health InjectionRHI Overview Routing to VIP Addresses Without RHI Routing to VIP Addresses With RHIUnderstanding How the CSM Determines VIP Availability Configuring RHI for Virtual ServersRouterconfig# ip slb vserver vserver1 Understanding Propagation of VIP Availability InformationSafety Information Referral Warning Translated Safety WarningsRegulatory Standards Compliance Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Qualified Personnel Warning Related DocumentationRelease Notes for Catalyst 6000 Family IOS Software Documentation CD-ROM Obtaining DocumentationWorld Wide Web Ordering DocumentationObtaining Technical Assistance Contacting TAC by Using the Cisco TAC WebsiteTo access Cisco.com, go to the following website Cisco.comContacting TAC by Telephone Obtaining Technical Assistance