Cisco Systems 6000 Features, These sections describe the CSM, Describes the features of the CSM

Page 3

Overview

These sections describe the CSM:

Features, page 3

Front Panel Description, page 4

Operation Mode, page 5

Client-to-CSM-to-Server Traffic Flow, page 7

Features

Table 1 describes the features of the CSM.

Table 1

Content Switching Module Features

 

 

 

Feature

 

Description

 

 

Management

Standard Cisco IOS command-line interface

 

 

Management interface integrated with host platform

 

 

Load-Balancing Algorithms

Weighted round-robin

 

 

Weighted least connections

 

 

Connection high/low watermarks

 

 

Source address-based hashing algorithm

 

 

Flow and URL Identification

URL regular expression match

 

 

Cookie regular expression match

 

 

SSL1 session ID match

 

 

Source IP address

 

 

Standard ACLs

 

 

 

Security

 

Source IP address and URL expression match and AC entry match

 

 

 

Statistics

 

Packets through normal and special switching

 

 

Connections created, established, destroyed, current, and timed out

 

 

Failed server connections

 

 

Layer 4 load-balanced decisions and rejected connections

 

 

Layer 7 load-balanced decisions and rejected connections

 

 

Layer 4 and Layer 7 rejected connections

 

 

Checksum failures

 

 

Redirect and FTP connections

 

 

MAC frames

 

 

 

 

 

Catalyst 6000 Family Content Switching Module Installation and Configuration Note

 

 

 

 

 

 

 

78-11631-02 Rev. A0

 

 

3

 

 

 

 

 

Image 3
Contents Contents Overview Features Describes the features of the CSMThese sections describe the CSM CSM front panel features are shown in Figure Front Panel DescriptionStatus LED Operation Mode RJ-45 ConnectorOff Red Orange Green Green to Orange Content Switching Module and Servers Client-to-CSM-to-Server Traffic Flow Client-to-Content Switching Module-to-Server Traffic FlowSafety Overview CSM memory is not configurable System RequirementsMemory Requirements 72-876-01 Console Cable Not applicable Power RequirementsHardware Supported Environmental RequirementsSoftware Requirements Installing the Content Switching ModulePreparing to Install the CSM Required ToolsInstalling the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the InstallationUsing the Command-Line Interface Accessing Online HelpUpgrading to a New Software Release Routerconfig# power cycle module slot-number Upgrading from the Supervisor Engine BootflashSet up a session between the supervisor engine and the CSM CSM upgrade 127.0.0.zz c6slb-apc.revision-num.binUpgrading from a Pcmcia Card Routerconfig# tftp-server slotxc6slb-apc.revision-num.binCSM upgrade slot0 c6slb-apc.revision-num.bin Router config# power cycle module slot-numberRouter# vlan database Configuring the Content Switching ModuleSwitchport Switchport access vlanConfiguration Overview Configure the required parameters in the following sections Configuring VLANsSee for the following notes Configuring VLANsConfiguring Server-Side VLANs Configuring Client-Side VLANsConfiguring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies Configure multiple cookies into a cookie mapConfiguring Sticky Groups Configuring Virtual Servers Configuring Dynamic Feedback Protocol Configuring TCP ParametersConfiguring Redirect Virtual Servers Configuring Client NAT Pools Configuring Server NAT Writing and Restoring ConfigurationsSingle Subnet Bridge Mode Configuration Configuration ExamplesExit to have the configuration take effect Enter the Vlan modeConfigure a client-side Vlan Configure a server-side VlanSecure Router Mode Configuration Vlan modeCreate the client-side Vlan 2 and enter the SLB Exit the submode Fault-Tolerant ConfigurationRouterconfig# ip slb vlan 3 server Create the server-side Vlan 3 and enter the SLBRouterconfig-if#service-policy input Venus Router# configure terminalRouterconfig# mac access-list extended Venus Routerconfig# int GigabitEthernet 2/1Configuration Parameter On Both Content Switching Modules Fault-tolerant configuration, the following rules apply192.158.38.10 Create the client-side Vlan 2 and enter the SLB Vlan modeAssign the Content Switching IP address on Router B Hsrp addressConfigure a client-side VLAN2 Assign the default route for VlanDefine Vlan 9 as a fault-tolerant Vlan Create the Content Switching primaryHsrp Configuration Overview Configuring HsrpCSG Vlan Configure Switch 2-FT2 Hsrp secondary as followsConfigure VLANs on Hsrp FT2 as follows Configuring CSM VLANsConfiguring Probes for Health Monitoring Configure EtherChannel on both switches as followsAdd ports to the EtherChannel as follows Telnet creates a Telnet probe with a default configuration Probe-name is the name of the probe being configured it hasHttp creates an Http probe with a default configuration Icmp creates an Icmp probe with a default configurationHttp Probe Commands Available to all Probe ConfigurationsIcmp Probe TCP Probe FTP, SMTP, and Telnet ProbeDNS Probe Submode Configuring Route Health Injection Understanding RHIRHI Overview Routing to VIP Addresses With RHI Routing to VIP Addresses Without RHIUnderstanding Propagation of VIP Availability Information Configuring RHI for Virtual ServersRouterconfig# ip slb vserver vserver1 Understanding How the CSM Determines VIP AvailabilityTranslated Safety Warnings Safety Information Referral WarningRegulatory Standards Compliance Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Related Documentation Qualified Personnel WarningRelease Notes for Catalyst 6000 Family IOS Software Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMCisco.com Contacting TAC by Using the Cisco TAC WebsiteTo access Cisco.com, go to the following website Obtaining Technical AssistanceContacting TAC by Telephone Obtaining Technical Assistance