Cisco Systems 6000 manual Configuration Examples, Single Subnet Bridge Mode Configuration

Page 35

Configuration Examples

Configuration Examples

Caution All examples assume that the ip slb mode csm command has been entered as described in “Configuring the Content Switching Module” section on page 19.

These examples show how to configure Content Switching in the following configurations:

•Single Subnet (Bridge) Mode Configuration, page 35

•Secure (Router) Mode Configuration, page 37

•Fault-Tolerant Configuration, page 38

•Configuring HSRP, page 43

Single Subnet (Bridge) Mode Configuration

In the single subnet (bridge) mode configuration, the client- and server-side VLANs are on the same subnets. Figure 9 shows how the single subnet (bridge) mode configuration is set up.

Figure 9 Single Subnet (Bridge) Mode Configuration

Client Services Gateway Client-side Server-side 192.158.38.10 192.158.38.10

Virtual server 1 192.158.38.30 Gateway

192.158.38.20

Router A

ClientNAS

workstation router

VLAN 2

Router B

Gateway

192.158.38.21

VLAN 3

Content provider

Server A Server B Server Farm 1

48428

Note The addresses in Figure 9 refer to the steps in the following task table.

		Catalyst 6000 Family Content Switching Module Installation and Configuration Note

	78-11631-02 Rev. A0			35
	78-11631-02 Rev. A0			35

Image 35

Contents Contents Overview These sections describe the CSM FeaturesDescribes the features of the CSM Status LED CSM front panel features are shown in FigureFront Panel Description Off Red Orange Green Green to Orange Operation ModeRJ-45 Connector Content Switching Module and Servers Client-to-CSM-to-Server Traffic Flow Client-to-Content Switching Module-to-Server Traffic FlowSafety Overview Memory Requirements CSM memory is not configurableSystem Requirements 72-876-01 Console Cable Not applicable Power RequirementsHardware Supported Environmental RequirementsSoftware Requirements Installing the Content Switching ModulePreparing to Install the CSM Required ToolsInstalling the CSM Power supply Installing Modules in the Catalyst 6000 Family Switch Verifying the Installation Verifying the InstallationUpgrading to a New Software Release Using the Command-Line InterfaceAccessing Online Help Routerconfig# power cycle module slot-number Upgrading from the Supervisor Engine BootflashSet up a session between the supervisor engine and the CSM CSM upgrade 127.0.0.zz c6slb-apc.revision-num.binUpgrading from a Pcmcia Card Routerconfig# tftp-server slotxc6slb-apc.revision-num.binCSM upgrade slot0 c6slb-apc.revision-num.bin Router config# power cycle module slot-numberRouter# vlan database Configuring the Content Switching ModuleSwitchport Switchport access vlanConfiguration Overview Configure the required parameters in the following sections Configuring VLANsSee for the following notes Configuring VLANsConfiguring Server-Side VLANs Configuring Client-Side VLANsConfiguring Server Farms Configuring Real Servers Configuring Policies Configuring Maps Configure multiple cookies Configure multiple cookies into a cookie mapConfiguring Sticky Groups Configuring Virtual Servers Configuring Dynamic Feedback Protocol Configuring TCP ParametersConfiguring Redirect Virtual Servers Configuring Client NAT Pools Configuring Server NAT Writing and Restoring ConfigurationsSingle Subnet Bridge Mode Configuration Configuration ExamplesExit to have the configuration take effect Enter the Vlan modeConfigure a client-side Vlan Configure a server-side VlanCreate the client-side Vlan 2 and enter the SLB Secure Router Mode ConfigurationVlan mode Exit the submode Fault-Tolerant ConfigurationRouterconfig# ip slb vlan 3 server Create the server-side Vlan 3 and enter the SLBRouterconfig-if#service-policy input Venus Router# configure terminalRouterconfig# mac access-list extended Venus Routerconfig# int GigabitEthernet 2/1Configuration Parameter On Both Content Switching Modules Fault-tolerant configuration, the following rules apply192.158.38.10 Create the client-side Vlan 2 and enter the SLB Vlan modeAssign the Content Switching IP address on Router B Hsrp addressConfigure a client-side VLAN2 Assign the default route for VlanDefine Vlan 9 as a fault-tolerant Vlan Create the Content Switching primaryHsrp Configuration Overview Configuring HsrpCSG Vlan Configure Switch 2-FT2 Hsrp secondary as followsConfigure VLANs on Hsrp FT2 as follows Configuring CSM VLANsAdd ports to the EtherChannel as follows Configuring Probes for Health MonitoringConfigure EtherChannel on both switches as follows Telnet creates a Telnet probe with a default configuration Probe-name is the name of the probe being configured it hasHttp creates an Http probe with a default configuration Icmp creates an Icmp probe with a default configurationHttp Probe Commands Available to all Probe ConfigurationsIcmp Probe DNS Probe Submode TCP ProbeFTP, SMTP, and Telnet Probe RHI Overview Configuring Route Health InjectionUnderstanding RHI Routing to VIP Addresses With RHI Routing to VIP Addresses Without RHIUnderstanding Propagation of VIP Availability Information Configuring RHI for Virtual ServersRouterconfig# ip slb vserver vserver1 Understanding How the CSM Determines VIP AvailabilityRegulatory Standards Compliance Translated Safety WarningsSafety Information Referral Warning Wrist Strap Warning Blank Faceplate Installation Requirement Warning Translated Safety Warnings Release Notes for Catalyst 6000 Family IOS Software Related DocumentationQualified Personnel Warning Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMCisco.com Contacting TAC by Using the Cisco TAC WebsiteTo access Cisco.com, go to the following website Obtaining Technical AssistanceContacting TAC by Telephone Obtaining Technical Assistance