Cisco Systems SFS 7012 manual Bringing Up the System For the First Time, Connecting Power

Page 47

Chapter

Note When handling IB connectors, make certain to remove the connectors by pulling on the center of the lanyard only as shown in Figure 2-13below. Pulling abruptly on the lanyard, or pulling on only one side of the lanyard will prevent the latch/unlatch operation from occurring, and could damage or break the lanyard.

Figure 2-13 4X IB Cable Connector

Connecting Power

Step 1 Provide strain relief for the power cable(s) by feeding them into the heyclips on the lower rail assemblies.

Note Be certain that the power cords are firmly seated into the SFS 7012 AC power inlets. Depending upon the purchased configuration, refer to Figure 2-12for which AC power inlet to use.

Step 2 If necessary, replace the faceplates over the switch fans.

Step 3 Connect the power cables to an AC power outlet.

Step 4 When the SFS 7012 switch is plugged into an AC power outlet:

a.The system powers up.

b.The fans start.

c.The system performs a power-on self test (POST).

Step 5 The switch, power supply, and fan LEDs light up.

Bringing Up the System For the First Time

Start-up Procedures

Step 1 Power up the SFS 7012.

Step 2 From its flash image on the CMU spine module, the switch begins its boot process.

Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide

 

OL-8787-04

29

 

 

 

Image 47
Contents Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide Page Preface Audience Connect Equipment to the Ports and Power On the System Snmp Configuring the Switch Default Gateway IP Address Capture Deprecated OL-8787-04 Initial release of the Cisco SFS New and Changed InformationViii Organization AudienceCisco.com ConventionsRelated Documentation Obtaining DocumentationProduct Documentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview Product Alerts and Field Notices Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Obtaining Technical AssistanceObtaining Additional Publications and Information Submitting a Service RequestDefinitions of Service Request Severity Page Xvi A P T E R SFS 7012 Feature SetKey Design Features Strategic BenefitsPower Design Features SFS 7012 Product SpecificationsMechanical/Thermal/Power Specifications Thermal Management FeaturesChassis Viewer Functionality Chassis Viewer SoftwareChapter Subnet Management Agents Subnet ManagerSubnet Management InfiniBand General Services Managers and Agents Snmp MIBs Snmp SupportOL-8787-04 Installation Statement 1019-Main Disconnecting Device Statement 1045-Short-circuit Protection Chapter Chapter Chapter Environmental Requirements Planning the InstallationAssembly 90-Degree Bend Radii Rack Specifications and RecommendationsInstalling and Routing Cable Uninterruptible Power Supply Power RequirementsPower Supply Safety Information Installation Tasks ChecklistElectrical Safety Precautions Tools and Equipment Required Unpack the Equipment Check the Installation SiteMounting Kit Installation TasksInstall the Rails in the Rack Mounting Hardware Kit ContentsRail Front Flange Rack-Mount the Switch Installing the Switch Face Plate Removing a Module or Blank Installing the Spine and Leaf ModulesLeaf Connect Equipment to the Ports and Power On the SystemLeaf Bringing Up the System For the First Time Connecting PowerStart-up Procedures Unmanaged Fan Managed System prompts for a password. At the prompt enter Reboot NEW IP Address Chassis Status LED SFS 7012 Component LEDsVerifying Start-up SFS 7012 Leaf and Spine Module LEDs Spine Module Management LEDs Spine and Leaf Module Status LEDSpine and Leaf Module Attention LED 15 Chassis Viewer Online Help Buttons Accessing On-line HelpRebooting Multiple Managed Spines Shutdown ProceduresRebooting Components from Chassis Viewer Hot Swapping Spine and Leaf Modules Hot Swapping ComponentsHot Swapping the Fan Unit Hot Swapping Power SuppliesChassis Viewer Manages Chassis ViewerSupport Button Home? Help Button Leaf Module View Displaying the Leaf and Spine Module ViewsSpine Module View Leaf and Spine Module Component Details AreaApply Leaf and Spine Details HeaderLeaf and Spine Information Area Displaying the Chassis ViewLeft click the mouse. The chassis view will be displayed Chassis Details Header Chassis View Component Details Area15 Reboot Screen LEDs and Sensors Tab Chassis View Component Information AreaChassis View Component Information Area Tabs System Information TabSystem Tab Chassis FRU Tab Power TabBackplane Tab Modifying Switch Component InformationFan Tab Logging Configuration and Monitoring FeaturesChassis View Menu 20 Logging Submenu Set Level23 Device Tab Software Module Configurator 24 Log System Configurator Preset Tab Preset TabSyslog Tab Reset Log LevelsConfigure Syslog on a Linux Server 27 Reset Log Levels Window Firmware UpdateSelect Target Configuration Target ConfigurationSnmp Target Addresses Target Configuration Window Field DescriptionsSnmp Target Parameters 33 Filter Status Button Filter Status34 Filter Status Screen Setting Community Strings36 Set Community Strings Window Chassis TrapsIcsChassisTrapModuleReboot IcsChassisTrapSystemRebootIcsChassisTrapSystemSwitchFailover IcsChassisTrapModuleBulkPowerFailureIcsChassisTrapPowerSupplyEEPROMReadFailure IcsChassisTrapPowerSupplyInsertedIcsChassisTrapPowerSupplyRemoved IcsChassisTrapPowerSupplyFailedLeaf modules/ports Interswitch Link ISL PortsSFS 7012 Port Statistics Understanding Port Naming ConventionsInfiniBand Statistics Port Statistics Field DescriptionsRemote Physical Error Received Symbol ErrorsLink Error Recovery Receive ErrorsSpine Modules Leaf and Spine Module IB Port StatisticsLeaf Modules 44 Spine Port Statistics Window Set Field ThresholdsPortRecvPktsThresh PortXmitDataThreshPortRecvDataThresh PortXmitPktsThreshTime Service Click the Use Network Time Protocol? checkbox 47 Switch Time ServiceDaylight Saving Time Tips Time Zone TipsFrom the OOB LAN IP submenu, click Set Default Gateway IP Configuring the Switch OOB IP AddressConfiguring the Switch Default Gateway IP Address Type in the correct switch default gateway IP address Viewing the Log Spine View MenuSelect Edit, Paste or Ctrl + Purging the LogSelect Edit, Copy or Ctrl + C License Keys Key Administration Select Boot ImageDeleting a License Key Adding a New License KeyClick OK to delete Technical Specifications OL-8787-04 Operator AdministratorOverview Commands and Functional Groups Capture Accessing the CLIOnline Help Keyboard ShortcutsGeneral Groups and CommandsSmGetPriority DeprecatedSample Output ChassisNetwork KeyManagement FirmwareLog TimeManagement IbSwitchInfoCapture Hardware Checks SwitchPower Supply Problem FixSFS 7012 Leaf Module IB Ports OOB Ethernet RJ45 PortBad IB Cable Troubleshooting ScenariosInfiniBand Invalid IP Address entered for SWC via Console PortOL-8787-04
Related manuals
Manual 176 pages 44.32 Kb