Cisco Systems SFS 7012 manual Time Zone Tips, Daylight Saving Time Tips

Page 93

Chapter

Step 1 Make sure the Use Network Time Protocol? checkbox is unchecked.

Step 2 Set the current date and time using the drop-downs for Month, Day, and Year as well as Hour, Minute, Seconds, and AM/PM.

Step 3 To save, click on Apply.

Figure 3-50 Time Service - Manual Setup

To set time zone and daylight saving time (DST) settings:

Step 1 In the Time Zone drop-down, select the correct time zone based upon Greenwich Mean Time (GMT). Step 2 Using the Which, Day, in Month drop-downs, set the start and end dates for daylight saving time. Step 3 To save, click on Apply.

Figure 3-51 Time Service - Time Zone/Daylight Saving Time Setup

Time Zone Tips:

In the U.S. the following time zones are in effect:

Eastern Standard Time = GMT –5

Central Standard Time = GMT –6

Mountain Standard Time = GMT –7

Pacific Standard Time = GMT -8

Daylight Saving Time Tips:

For most of the United States, Daylight Saving Time begins at 2 a.m. on the first Sunday of April, and ends at 2 a.m. on the last Sunday of October. Using this information, the Daylight Saving Time Start Date will always be the 1st Sunday in April. However, the Daylight Saving Time End Date will vary between the 4th and 5th Sunday of October. Be certain to check a calendar when setting this parameter. Following are upcoming DST end dates:

Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide

 

OL-8787-04

75

 

 

 

Image 93
Contents Cisco SFS 7012 InfiniBand Server Switch Hardware Users Guide Page Preface Audience Connect Equipment to the Ports and Power On the System Snmp Configuring the Switch Default Gateway IP Address Capture Deprecated OL-8787-04 Initial release of the Cisco SFS New and Changed InformationViii Organization AudienceRelated Documentation ConventionsObtaining Documentation Cisco.comDocumentation Feedback Cisco Product Security OverviewProduct Documentation DVD Ordering Documentation Product Alerts and Field Notices Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Obtaining Technical AssistanceSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information Page Xvi Key Design Features SFS 7012 Feature SetStrategic Benefits A P T E RMechanical/Thermal/Power Specifications SFS 7012 Product SpecificationsThermal Management Features Power Design FeaturesChassis Viewer Functionality Chassis Viewer SoftwareChapter Subnet Manager Subnet ManagementSubnet Management Agents InfiniBand General Services Managers and Agents Snmp MIBs Snmp SupportOL-8787-04 Installation Statement 1019-Main Disconnecting Device Statement 1045-Short-circuit Protection Chapter Chapter Chapter Environmental Requirements Planning the InstallationRack Specifications and Recommendations Installing and Routing CableAssembly 90-Degree Bend Radii Power Requirements Power SupplyUninterruptible Power Supply Safety Information Installation Tasks ChecklistElectrical Safety Precautions Tools and Equipment Required Unpack the Equipment Check the Installation SiteInstall the Rails in the Rack Installation TasksMounting Hardware Kit Contents Mounting KitRail Front Flange Rack-Mount the Switch Installing the Switch Face Plate Removing a Module or Blank Installing the Spine and Leaf ModulesLeaf Connect Equipment to the Ports and Power On the SystemLeaf Connecting Power Start-up ProceduresBringing Up the System For the First Time Unmanaged Fan Managed System prompts for a password. At the prompt enter Reboot NEW IP Address SFS 7012 Component LEDs Verifying Start-upChassis Status LED SFS 7012 Leaf and Spine Module LEDs Spine and Leaf Module Status LED Spine and Leaf Module Attention LEDSpine Module Management LEDs 15 Chassis Viewer Online Help Buttons Accessing On-line HelpShutdown Procedures Rebooting Components from Chassis ViewerRebooting Multiple Managed Spines Hot Swapping Spine and Leaf Modules Hot Swapping ComponentsHot Swapping the Fan Unit Hot Swapping Power SuppliesChassis Viewer Manages Chassis ViewerHome ? Help ButtonSupport Button Leaf Module View Displaying the Leaf and Spine Module ViewsSpine Module View Leaf and Spine Module Component Details AreaLeaf and Spine Information Area Leaf and Spine Details HeaderDisplaying the Chassis View ApplyLeft click the mouse. The chassis view will be displayed Chassis Details Header Chassis View Component Details Area15 Reboot Screen Chassis View Component Information Area Tabs Chassis View Component Information AreaSystem Information Tab LEDs and Sensors TabSystem Tab Chassis FRU Tab Power TabModifying Switch Component Information Fan TabBackplane Tab Configuration and Monitoring Features Chassis View MenuLogging 20 Logging Submenu Set Level23 Device Tab Software Module Configurator 24 Log System Configurator Preset Tab Preset TabReset Log Levels Configure Syslog on a Linux ServerSyslog Tab 27 Reset Log Levels Window Firmware UpdateSelect Target Configuration Target ConfigurationSnmp Target Addresses Target Configuration Window Field DescriptionsSnmp Target Parameters 33 Filter Status Button Filter Status34 Filter Status Screen Setting Community Strings36 Set Community Strings Window Chassis TrapsIcsChassisTrapSystemSwitchFailover IcsChassisTrapSystemRebootIcsChassisTrapModuleBulkPowerFailure IcsChassisTrapModuleRebootIcsChassisTrapPowerSupplyRemoved IcsChassisTrapPowerSupplyInsertedIcsChassisTrapPowerSupplyFailed IcsChassisTrapPowerSupplyEEPROMReadFailureSFS 7012 Port Statistics Interswitch Link ISL PortsUnderstanding Port Naming Conventions Leaf modules/portsInfiniBand Statistics Port Statistics Field DescriptionsLink Error Recovery Symbol ErrorsReceive Errors Remote Physical Error ReceivedLeaf and Spine Module IB Port Statistics Leaf ModulesSpine Modules 44 Spine Port Statistics Window Set Field ThresholdsPortRecvDataThresh PortXmitDataThreshPortXmitPktsThresh PortRecvPktsThreshTime Service Click the Use Network Time Protocol? checkbox 47 Switch Time ServiceDaylight Saving Time Tips Time Zone TipsConfiguring the Switch OOB IP Address Configuring the Switch Default Gateway IP AddressFrom the OOB LAN IP submenu, click Set Default Gateway IP Type in the correct switch default gateway IP address Viewing the Log Spine View MenuPurging the Log Select Edit, Copy or Ctrl + CSelect Edit, Paste or Ctrl + License Keys Key Administration Select Boot ImageDeleting a License Key Adding a New License KeyClick OK to delete Technical Specifications OL-8787-04 Administrator OverviewOperator Commands and Functional Groups Online Help Accessing the CLIKeyboard Shortcuts CaptureGeneral Groups and CommandsSmGetPriority DeprecatedSample Output ChassisNetwork Firmware LogKeyManagement TimeManagement IbSwitchInfoCapture Power Supply SwitchProblem Fix Hardware ChecksSFS 7012 Leaf Module IB Ports OOB Ethernet RJ45 PortInfiniBand Troubleshooting ScenariosInvalid IP Address entered for SWC via Console Port Bad IB CableOL-8787-04
Related manuals
Manual 176 pages 44.32 Kb