Cisco Systems 3750-X, 3560-X manual Installing Network Modules

Page 56

Chapter 2 Switch Installation

Installing a Network Module in the Switch

Use only Cisco network modules and SFP or SFP+ modules with the switch. For information about supported SFP modules, see the “SFP and SFP+ Modules” section on page 1-5.

For more information about installing, removing, cabling, and troubleshooting network modules, see the module documentation on Cisco.com. For module cable specifications, see Appendix B, “Connector and Cable Specifications.”

Tools and Equipment

You need to supply a number-2 Phillips screwdriver.

Installing Network Modules

When installing network modules, observe these general precautions:

Do not remove the EMC plug from the 10-Gigabit Ethernet slot until you are ready to install an SFP or SFP+ module. Either a module or a dust plug must be installed in the slot at all times.

Do not remove the dust plugs from the fiber-optic SFP modules or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the module ports and cables from contamination and ambient light.

Removing and installing a network module can shorten its useful life. Do not remove and insert any network module more often than necessary.

To prevent ESD damage, follow your normal board and component handling procedures when connecting cables to the switch and other devices.

Step 1 Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.

Step 2 Remove the module from the protective packaging.

Step 3 Remove the 10-Gigabit Ethernet module slot EMC plug and save.

Caution Verify the correct orientation of your module before inserting it into the slot. Incorrect insertion can damage the module.

Step 4 Position the module face up to install in the module slot. See Figure 2-25. Slide the module into the opening until the back of the module faceplate is flush with the switch faceplate. Fasten the captive screws to secure the network module in place.

Caution Do not insert or remove a network module with attached fiber-optic cables. A module interface might change to an error-disabled state when a network module is inserted or removed with connected fiber-optic cables. If the interface is in an error-disabled state, you can re-enable the interface by using the shutdown and no shutdown interface configuration commands.

 

Catalyst 3750-X and 3560-X Switch Hardware Installation Guide

2-24

OL-19593-01

Image 56
Contents Americas Headquarters Text Part Number OL-19593-01Page N T E N T S Attaching the Rack-Mount Brackets Where to Go Next SFP and SFP+ Module Cable Specifications B-5 Vii Viii Related Publications Catalyst 3750-X switches Catalyst 3560-X switchesPurpose Obtaining Documentation and Submitting a Service Request Switch Models Switch Model Cisco IOS Image DescriptionSwitch Part Number Description PoE+ Ports Front Panel Description10/100/1000 Ethernet Ports Network Modules SFP and SFP+ Modules Network Module DescriptionPart Number Description SFP-10G-LR= SFP-10G-SR=SFP-10G-LRM= SFP-H10GB-CU1M=LEDs SFP-H10GB-CU3M=SFP-H10GB-CU5M= XPS 1 LEDSystem LED Port LEDs and ModesColor System Status Color XPS StatusMode LED Port Mode Description Port Mode Port LED Color MeaningUSB Console LED PWR LED Catalyst Master LED CatalystStack LED Catalyst ColorPoE+ LED Color PoE+ StatusUSB Mini-Type B Port Network Module LEDsG1 LED G3 LED G2/TE1 LED G4/TE2 LED Color Network Module Link StatusCatalyst 3560-X Switch Rear Panel Rear Panel DescriptionRS-232 console is disabled RS-232 console is enabled RJ-45 Console Port LEDUSB Type a Interface StackWise PortsPort Port PoE+ Non-PoE+ Power Supply Module Switch1 Power Supply ModulesSwitch Power Supply Modules Port Port PoE+ Non-PoE+ Power Supply Module Switch PoE Option Port SwitchAC-Power Supply Module LEDs DC-Power Supply Module LEDsXPS Connector Fan ModulesStackPower Connector Catalyst 3750-X Switches Management PortsEthernet Management Port Active link to PCManagement Options USB Mini-Type B PortOff Amber Inactive link Post failureNetwork Configurations Preparing for Installation Safety WarningsOL-19593-01 Installation Guidelines Statement 371-Power Cable and AC AdapterPlanning a Switch Data Stack Catalyst 3750-X Switches Tools and EquipmentData Stack Cabling Configurations Switch Data Stacking Guidelines3-meter StackWise Cables Data Stack Bandwidth and Partitioning Examples Example of a Data Stack with Half Bandwidth ConnectionsStackPower Stacking Guidelines Planning a StackPower Stack Catalyst 3750-X SwitchesPower On Sequence for Switch Data Stacks StackPower Cabling Configurations Part Number Cable Type Length CAB-SPWR-30CMCAB-SPWR-150CM CAB-XPS-58CM10 StackPower Ring Topology 253397 253398 Rack-Mounting Installing the SwitchStackPower Partitioning Examples Switch Installation Installing the Switch Etsi brackets, part number Inch brackets, part number23/24-inch brackets, part number Attaching the Rack-Mount Brackets 18 Attaching Brackets for 19-inch RacksMounting the Switch in a Rack Mounting the Switch in a Rack Table- or Shelf-Mounting 20 Attaching the Adhesive Pads for Table- or Shelf-MountingConnecting to the StackWise Ports Catalyst 3750-X Switches After Installing the SwitchConnecting to the StackPower Ports Catalyst 3750-X Switches Connecting the StackPower Ports to the XPS-2200 Installing a Network Module in the SwitchInstalling Network Modules You need to supply a number-2 Phillips screwdriverInstalling SFP and SFP+ Modules Removing a Network ModuleInstalling an SFP Module 26 Installing an SFP Module in the Network ModuleConnecting Devices to the Ethernet Ports Removing an SFP ModuleDevice Crossover Cable 10/100/1000 Ethernet Port ConnectionsPoE+ Port Connections Where to Go Next Start an Snmp application such as the CiscoView application Power Supply and Fan Module Installation Power Supply Module OverviewBlank cover DC power supply moduleC3KX-PWR-715WAC= AC power supply module AC power cord connector Power cord retainerAC OK LED Release latchExtraction handle DC power supply module Grounding terminalDC OK LED Installation Guidelines AC Power Supply Module LEDsDC Power Supply Module LEDs Release handles Retainer clipsInstalling an AC Power Supply Turn off the power at its sourceRemove the power cord from the power cord retainer Remove the power cord from the power connectorInstalling a DC Power Supply Inserting the AC-Power Supply in the SwitchEquipment That You Need Grounding the Switch Stripping the Ground WireInstalling the DC Power Supply in the Switch See the Installation Guidelines,Wiring the DC Input Power Source 11 Inserting the DC Power Supply in the SwitchFinding the Power Supply Module Serial Number 13 DC Source a and Source B Connections with Common Ground15 715-W and 350-W AC Power Supply Module Serial Number Fan Module Overview Fan ModuleFan LED Retainer clip Exhaust vent Extraction handles Installing a Fan ModuleFinding the Fan Module Serial Number 19 Fan Module Serial Number Switch LEDs Diagnosing ProblemsSwitch Post Results Switch Connections Bad or Damaged CableEthernet and Fiber Cables Link StatusSFP Modules 10/100/1000 Port ConnectionsPoE Port Connections Switch Performance Interface SettingsPing End Device Spanning Tree LoopsCabling Distance Resetting the Switch to the Factory Default SettingsAutonegotiation and Network Interface Cards Finding the Switch Serial Number Switch Serial Number LocationEnvironmental Ranges Switch SpecificationsPhysical Specifications Power Supply Module Specifications Power Specifications C3KX-PWR-1100WACC3KX-PWR-715WAC C3KX-PWR-350WACFan Module Specifications Physical SpecificationOperating Specification Airflow 60 cfmDescription Specification MICChina EMC certifications GostOL-19593-01 Connector Specifications 10/100/1000 PortsGigabit Ethernet CX1 SFP+ Copper Connectors Figure B-2 10-Gigabit Ethernet CX1 Copper Connector exampleFigure B-4 Simplex LC Cable Connector 10/100 Ethernet Management PortConsole Port Figure B-7 10/100 Port PinoutsCable and Adapter Specifications SFP and SFP+ Module Cable SpecificationsGLC-T 1000BASE-LX/LHMMF3 GLC-LH-SMFour Twisted-Pair Cable Pinouts Two Twisted-Pair Cable PinoutsSwitch Console RJ-45-to-DB-9 Port DTE Identifying a Crossover CableConsole Port Adapter Pinouts DeviceSwitch Console RJ-45-to-DB-25 Port DTE GNDRxD TxD DSR DTR CTS RTSOL-19593-01 Accessing the CLI Through a Console Port Accessing the CLIAccessing the CLI Through Express Setup USB Console Port Use one of these options to access the CLIRJ-45 Console Port Installing the Cisco Microsoft Windows USB Device Driver ModeInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows 2000 USB DriverUninstalling the Cisco Microsoft Windows USB Driver Using the Add or Remove Programs utilityConfiguring the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return These choices appear Connectors and cables Console port Connectors and cables DescribedIN-2 Port mode Post results Speed Stack StackPower StatusProduct disposal warning Power-supply modulePost Connector Described LED XPSIN-6