Cisco Systems PA-4C-E 1 manual Removing and Installing Port Adapters, Handling Port Adapters

Page 21

Removing and Installing Port Adapters

Removing and Installing Port Adapters

This section describes how to remove port adapters from supported platforms and also how to install new or replacement port adapters.This section contains the following subsections:

Handling Port Adapters, page 21

Online Insertion and Removal, page 22

Port Adapter Removal and Installation, page 23

Attaching the HP ESCON PA to the Channel, page 25

Handling Port Adapters

Each port adapter circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge (ESD) damage.

Note When a slot is not in use, a blank port adapter must fill the empty slot to allow the router or switch to conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow across the installed port adapters. If you plan to install a new port adapter in a slot that is not in use, you must first remove the blank port adapter.

Caution Always handle the port adapter by the carrier edges and handle; never touch the port adapter components

or connector pins. Always use an ESD wrist strap when handling equipment. (See Figure 7.)

Figure 7

Handling a Port Adapter

Metal carrier

Printed circuit board

H6420

PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration

 

OL-3743-02

21

 

 

 

Image 21
Contents PA-4C-E 1-Port High-Performance Objectives Document Revision HistoryOrganization Document Version Date Change SummaryRelated Documentation OL-3743-02 Port Adapter Overview OverviewCisco 7206 with an HP Escon PA in Port Adapter Slot Escon Specifications Characteristic Escon SpecificationLEDs Off Sequence Present Loaded Signal OnlinePort Adapter Slot Locations on the Supported Platforms Escon CablePort Adapter Slots in the Cisco 7206 Router Identifying Interface AddressesPlatform Interface Address Format Numbers Syntax HP Escon PA Microcode Overview Required Tools and EquipmentRouter# show microcode Hardware and Software RequirementsCisco IOS Release Image Names Checking Hardware and Software CompatibilitySafety Warnings Safety GuidelinesWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar Laser LED Safety Information Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Laser Radiation Staring into Laser Beam Handling Port Adapters Removing and Installing Port AdaptersOnline Insertion and Removal Port Adapter Removal and Installation Step Attaching the HP Escon PA to the Channel Using the Exec Command Interpreter Configuring the HP Escon PAConfiguring the HP Escon PA Interface Performing a Basic Interface ConfigurationRouter# configure terminal Using show Commands to Verify the New Interface Status Checking the ConfigurationRouterconfig# interface channel 2/0 Routerconfig-if#ip address 1.1.1.10Router# show version Using the show version or show hardware CommandsRouter# show controllers channel 2/0 Using the show controllers CommandsRouter# show interface channel 4/0 Using the show diag CommandRouter# ping Using the Ping Command to Verify Network ConnectivityUpgrading Your HP Escon PA Microcode How Does HP Escon PA Microcode Ship?Upgrading the HP Escon PA Microcode from Cisco.com Router show flash Configuring the HP Escon PA MicrocodeRouterconfig# no microcode ecpa slot0xcpa28-1 Routerconfig# microcode ecpa slot0xcpa28-1Router# copy tftpxcpa28-6 slot0xcpa28-6 Using Flash MemoryUsing Additional Flash Memory Commands Router# cd slot0Router# squeeze slot0 Using SanDisk Devices Recovering from Locked BlocksTftpxcpa27-1 disk0xcpa27-1 Router# configuration term Running HP Escon PA Diagnostic TestsConfiguring the HP Escon PA