Cisco Systems PA-4C-E 1 Using the show controllers Commands, Router# show controllers channel 2/0

Page 30

Configuring the HP ESCON PA

X.25 software, Version 3.0.0.

4 Ethernet/IEEE 802.3 interface(s)

3 FastEthernet/IEEE 802.3 interface(s)

2 IBM channel interface(s)

125K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 4096K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x100

Using the show controllers Commands

Display all the current interface processors and their interfaces using the show controllers command.

Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.

Cisco 7200 Series and Cisco 7200 VXR Series Routers—Example Output of the show controllers Command

Following is an example of the show controllers command that displays information about a specific

HP ESCON PA:

Router# show controllers channel 2/0

ECPA 2, hardware version 1.0, microcode version 218.6

Mailbox commands:0 forevers, 0 max elapsed usecs

Microcode loaded from flash slot0:xcpa218-6_kernel_ecpa4

Loaded:seg_802

 

 

Rev. 0

Compiled by jdoe on Thu 07-Sep-2000 12:

Loaded:seg_csna

 

 

Rev. 0

Compiled by jdoe on Thu 07-Sep-2000 12:

Loaded:seg_eca

 

 

Rev. 0

Compiled by jdoe on Thu 07-Sep-2000 12:

Loaded:seg_sslc

 

 

Rev. 0

Compiled by jdoe on Thu 07-Sep-2000 12:

Loaded:seg_tcpip

 

 

Rev. 0

Compiled by jdoe on Thu 07-Sep-2000 12:

Loaded:seg_tn3270

 

 

Rev. 0

Compiled by jdoe on Thu 07-Sep-2000 12:

EPROM version 0.0, VPLD version 0.0

ECA0:hw version 02, microcode version C50602D4

Load metrics:

 

 

 

 

 

Memory

dram 118412048/128M

 

CPU

1m

1%,

5m

2%, 60m

2%

DMA

1m

1%,

5m

0%, 60m

0%

ECA0

1m

0%,

5m

0%, 60m

0%

Interface Channel2/0

Hardware is Escon Channel

HW Registers CPU init=0x021441A0 LED control=0x00045DDF Reset Satus=0x00000002

HW Poll Register 4B0D5240:[00000001]

Free buffer queues

queue=0 max_entries=128 size=600 head=71 ring=4B0EB060 queue=1 max_entries=32 size=4520 head=23 ring=4B07D380 queue=2 max_entries=64 size=4520 head=63 ring=4B07D440

Tx Queues

queue=0 head=0 tail=0 tx_cnt=0 tx_pakcnt=0

max_entries=128 type=1 poll_index=0 ring=4B07D580 fspak buffers swapped out=0

queue=1 head=12 tail=12 tx_cnt=0 tx_pakcnt=0

max_entries=32 type=2 poll_index=1 ring=4B0EB2A0 fspak buffers swapped out=0

Rx Queues

max_entries=221 poll_index=3 head=96 ring=4B0EB3E0

PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration

30

OL-3743-02

 

 

Image 30
Contents PA-4C-E 1-Port High-Performance Organization Document Revision HistoryObjectives Document Version Date Change SummaryRelated Documentation OL-3743-02 Overview Port Adapter OverviewCisco 7206 with an HP Escon PA in Port Adapter Slot Escon Specifications Characteristic Escon SpecificationLEDs Sequence Present Loaded Signal Online OffEscon Cable Port Adapter Slot Locations on the Supported PlatformsIdentifying Interface Addresses Port Adapter Slots in the Cisco 7206 RouterPlatform Interface Address Format Numbers Syntax Required Tools and Equipment HP Escon PA Microcode OverviewHardware and Software Requirements Router# show microcodeChecking Hardware and Software Compatibility Cisco IOS Release Image NamesSafety Guidelines Safety WarningsWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar Laser LED Safety Information Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Laser Radiation Staring into Laser Beam Removing and Installing Port Adapters Handling Port AdaptersOnline Insertion and Removal Port Adapter Removal and Installation Step Attaching the HP Escon PA to the Channel Configuring the HP Escon PA Using the Exec Command InterpreterConfiguring the HP Escon PA Interface Performing a Basic Interface ConfigurationRouter# configure terminal Routerconfig# interface channel 2/0 Checking the ConfigurationUsing show Commands to Verify the New Interface Status Routerconfig-if#ip address 1.1.1.10Using the show version or show hardware Commands Router# show versionUsing the show controllers Commands Router# show controllers channel 2/0Using the show diag Command Router# show interface channel 4/0Using the Ping Command to Verify Network Connectivity Router# pingUpgrading Your HP Escon PA Microcode How Does HP Escon PA Microcode Ship?Upgrading the HP Escon PA Microcode from Cisco.com Configuring the HP Escon PA Microcode Router show flashRouterconfig# microcode ecpa slot0xcpa28-1 Routerconfig# no microcode ecpa slot0xcpa28-1Using Flash Memory Router# copy tftpxcpa28-6 slot0xcpa28-6Using Additional Flash Memory Commands Router# cd slot0Router# squeeze slot0 Using SanDisk Devices Recovering from Locked BlocksTftpxcpa27-1 disk0xcpa27-1 Running HP Escon PA Diagnostic Tests Router# configuration termConfiguring the HP Escon PA