Cisco Systems PA-4C-E 1 Using the show version or show hardware Commands, Router# show version

Page 29

Configuring the HP ESCON PA

Step 3 Specify one of the new interfaces with the show interfaces port adapter type slot/interface command and verify that the first line of the display specifies the interface with the correct slot number. Also verify that the interface and line protocol are in the correct state: up or down.

Step 4 Display the protocols configured for the entire system and specific interfaces with the show protocols command. If necessary, return to configuration mode to add or remove protocol routing on the system or specific interfaces.

Step 5 Display the running configuration file with the show running-configcommand. Display the configuration stored in nonvolatile RAM (NVRAM) using the show startup-configcommand. Verify that the configuration is accurate for the system and each interface.

If the interface is down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, ensure that the network interface is properly connected and terminated. If you still have problems bringing up the interface, contact a service representative for assistance.

This section includes the following subsections:

•Using the show version or show hardware Commands, page 29

•Using the show controllers Commands, page 30

•Using the show diag Command, page 31

•Using the show interfaces Commands, page 31

Using the show version or show hardware Commands

Display the configuration of the router hardware, the software version, the names and sources of configuration files, and the boot images using the show version (or show hardware) command.

 

Note

The outputs that appear in this document may not match the output you receive when running these

 

 

commands. The outputs in this document are examples only.

 

 

 

 

 

Cisco 7200 Series and Cisco 7200 VXR Series Routers—Example Output of the show version Command

 

 

Following is an example of the show version command from a Cisco 7200 series router:

 

 

Router# show version

 

 

Cisco Internetwork Operating System Software

 

 

IOS (tm) 7200 Software (C7200-IS56I-M), Released Version 12.1

 

 

Copyright (c) 1986-2000 by cisco Systems, Inc.

 

 

Compiled Thu 27-Jul-00 13:22 by biff

 

 

Image text-base: 0x60008960, data-base: 0x613C4000

 

 

ROM: System Bootstrap, Version 12.1 RELEASE SOFTWARE (f)

 

 

BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.1, RELEASE SOFTWARE R

 

 

router uptime is 5 hours, 6 minutes

 

 

System returned to ROM by reload at 04:35:10 UTC Thu Aug 10 2000

 

 

System image file is "tftp://181.23.250.2/jdoe/c7200-is56i-mz.121-5.T"

 

 

cisco 7206VXR (NPE300) processor (revision B) with 122880K/40960K bytes of memo.

 

 

Processor board ID 15463825

 

 

R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache

 

 

6 slot VXR midplane, Version 2.0

 

 

Last reset from power-on

 

 

Bridging software.

 

 

PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration

 

 

 

 

 

 

 

OL-3743-02

 

 

29

 

 

 

 

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents PA-4C-E 1-Port High-Performance Objectives Document Revision HistoryOrganization Document Version Date Change SummaryRelated Documentation OL-3743-02 Port Adapter Overview OverviewCisco 7206 with an HP Escon PA in Port Adapter Slot LEDs Escon SpecificationsCharacteristic Escon Specification Off Sequence Present Loaded Signal OnlinePort Adapter Slot Locations on the Supported Platforms Escon CablePort Adapter Slots in the Cisco 7206 Router Identifying Interface AddressesPlatform Interface Address Format Numbers Syntax HP Escon PA Microcode Overview Required Tools and EquipmentRouter# show microcode Hardware and Software RequirementsCisco IOS Release Image Names Checking Hardware and Software CompatibilitySafety Warnings Safety GuidelinesAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Spara Dessa Anvisningar Preventing Electrostatic Discharge Damage Laser LED Safety InformationElectrical Equipment Guidelines Laser Radiation Staring into Laser Beam Handling Port Adapters Removing and Installing Port AdaptersOnline Insertion and Removal Port Adapter Removal and Installation Step Attaching the HP Escon PA to the Channel Using the Exec Command Interpreter Configuring the HP Escon PARouter# configure terminal Configuring the HP Escon PA InterfacePerforming a Basic Interface Configuration Using show Commands to Verify the New Interface Status Checking the ConfigurationRouterconfig# interface channel 2/0 Routerconfig-if#ip address 1.1.1.10Router# show version Using the show version or show hardware CommandsRouter# show controllers channel 2/0 Using the show controllers CommandsRouter# show interface channel 4/0 Using the show diag CommandRouter# ping Using the Ping Command to Verify Network ConnectivityUpgrading the HP Escon PA Microcode from Cisco.com Upgrading Your HP Escon PA MicrocodeHow Does HP Escon PA Microcode Ship? Router show flash Configuring the HP Escon PA MicrocodeRouterconfig# no microcode ecpa slot0xcpa28-1 Routerconfig# microcode ecpa slot0xcpa28-1Router# copy tftpxcpa28-6 slot0xcpa28-6 Using Flash MemoryRouter# squeeze slot0 Using Additional Flash Memory CommandsRouter# cd slot0 Tftpxcpa27-1 disk0xcpa27-1 Using SanDisk DevicesRecovering from Locked Blocks Router# configuration term Running HP Escon PA Diagnostic TestsConfiguring the HP Escon PA
Top Page Image Contents