Configuring the HP ESCON PA
Using the show diag Command
Display the type of port adapter installed in your system using the show diag command.
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.
Cisco 7200 Series and Cisco 7200 VXR Series
Following is an example of the show diag command from a Cisco 7200 series router with an HP ESCON PA installed in port adapter slot 4:
Router# show diag 2 |
|
|
|
|
|
|
|
| |
Slot 2: |
|
|
|
|
|
|
|
|
|
Escon Port adapter, 1 | port |
|
|
|
| ||||
Port adapter is | analyzed |
|
|
|
|
| |||
Port adapter insertion time 00:05:00 | ago |
|
| ||||||
EEPROM contents | at hardware discovery: |
|
| ||||||
Hardware Revision |
|
| :1.0 |
|
|
|
| ||
Top Assy. Part Number |
|
|
| ||||||
Part Number |
|
|
|
|
|
| |||
Board Revision |
|
|
| :02 |
|
|
|
| |
PCB Serial Number |
|
| :18902852000 |
|
|
| |||
RMA History |
|
|
| :00 |
|
|
|
| |
Fab Version |
|
|
| :02 |
|
|
|
| |
Fab Part Number |
|
|
|
|
|
| |||
Product Number |
|
|
|
|
|
|
| ||
EEPROM format version | 4 |
|
|
|
|
| |||
EEPROM contents | (hex): |
|
|
|
|
|
| ||
0x00:04 FF 40 | 02 10 | 41 | 01 00 C0 46 | 03 20 00 18 CB 02 | |||||
0x10:82 | 49 11 | 66 | 02 | 42 | 30 32 C1 | 8B | 31 38 39 30 | 32 | 38 |
0x20:35 32 30 | 30 30 | 04 | 00 02 02 85 | 1C 0D 4D 02 CB 94 | |||||
0x30:50 41 2D | 34 43 | 2D | 45 42 00 00 | 00 00 FF FF FF FF | |||||
0x40:FF FF FF | FF FF | FF | FF FF FF FF | FF FF FF FF FF FF | |||||
0x50:FF FF FF | FF FF | FF | FF FF FF FF | FF FF FF FF FF FF | |||||
0x60:FF FF FF | FF FF | FF | FF FF FF FF | FF FF FF FF FF FF | |||||
0x70:FF FF FF | FF FF | FF | FF FF FF FF | FF FF FF FF FF FF |
Using the show interfaces Commands
Display information about a specific interface using the show interfaces command.
Note The outputs that appear in this document may not match the output you receive when running these commands. The outputs in this document are examples only.
Cisco 7200 Series and Cisco 7200 VXR Series
Following is an example of the show interfaces channel command for an HP ESCON PA in port adapter slot 4:
Router# show interface channel 4/0
| Channel4/0 | is up, line protocol is up | |||
| Hardware | is Escon Channel | |||
| Internet | address is 10.10.99.1/24 | |||
| MTU 4472 | bytes, BW 98304 Kbit, DLY 100 usec, | |||
| reliability 255/255, txload 1/255, rxload 1/255 | ||||
| Encapsulation CHANNEL, loopback not set | ||||
| ECA adapter card | ||||
|
|
|
|
| |
|
|
| |||
|
|
| 31 |
| |
|
|
|
|