Cisco Systems PA-4C-E 1 manual Running HP Escon PA Diagnostic Tests, Router# configuration term

Page 39

Configuring the HP ESCON PA

Expanding disk0:xcpa27-1_seg_push (15488 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_tcpip (161140 bytes):!!!!!!!!!!! Expanding disk0:xcpa27-1_seg_tn3270 (620400 bytes):!!!!!!!!!!!

[OK - 2739200/5478400 bytes]

2739200 bytes copied in 68.500 secs (40282 bytes/sec)

To update your running configuration:

Step 1 Enter the following commands, beginning in global configuration mode:

Router# configuration term

Router(config)# microcode ecpa diskX:xcpaXX-YY

Router(config)# microcode reload

Router(config)# end

where:

diskX is disk0 or disk1 on the SanDisk device

xcpaXX-YYis the xCPA image you want to use, such as xcpa27-1

Step 2 Save the running configuration to NVRAM.

Running HP ESCON PA Diagnostic Tests

The HP ESCON PA diagnostic test routines are as follows:

Processor test 1

Processor test 2

I/O device tests

Serial link controller (SLC) device tests

Internal electrical wrap

External optical wrap for the ESCON Channel Port Adapter

Note All diagnostic tests are run every time the adapter is started. They cannot be run independently. The external optical wrap test require special wrap plugs for the HP ESCON PA. Contact a service representative to obtain the appropriate wrap plugs

PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration

 

OL-3743-02

39

 

 

 

Image 39
Contents PA-4C-E 1-Port High-Performance Document Version Date Change Summary Document Revision HistoryObjectives OrganizationRelated Documentation OL-3743-02 Port Adapter Overview OverviewCisco 7206 with an HP Escon PA in Port Adapter Slot Escon Specifications Characteristic Escon SpecificationLEDs Off Sequence Present Loaded Signal OnlinePort Adapter Slot Locations on the Supported Platforms Escon CablePort Adapter Slots in the Cisco 7206 Router Identifying Interface AddressesPlatform Interface Address Format Numbers Syntax HP Escon PA Microcode Overview Required Tools and EquipmentRouter# show microcode Hardware and Software RequirementsCisco IOS Release Image Names Checking Hardware and Software CompatibilitySafety Warnings Safety GuidelinesWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar Laser LED Safety Information Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Laser Radiation Staring into Laser Beam Handling Port Adapters Removing and Installing Port AdaptersOnline Insertion and Removal Port Adapter Removal and Installation Step Attaching the HP Escon PA to the Channel Using the Exec Command Interpreter Configuring the HP Escon PAConfiguring the HP Escon PA Interface Performing a Basic Interface ConfigurationRouter# configure terminal Routerconfig-if#ip address 1.1.1.10 Checking the ConfigurationUsing show Commands to Verify the New Interface Status Routerconfig# interface channel 2/0Router# show version Using the show version or show hardware CommandsRouter# show controllers channel 2/0 Using the show controllers CommandsRouter# show interface channel 4/0 Using the show diag CommandRouter# ping Using the Ping Command to Verify Network ConnectivityUpgrading Your HP Escon PA Microcode How Does HP Escon PA Microcode Ship?Upgrading the HP Escon PA Microcode from Cisco.com Router show flash Configuring the HP Escon PA MicrocodeRouterconfig# no microcode ecpa slot0xcpa28-1 Routerconfig# microcode ecpa slot0xcpa28-1Router# copy tftpxcpa28-6 slot0xcpa28-6 Using Flash MemoryUsing Additional Flash Memory Commands Router# cd slot0Router# squeeze slot0 Using SanDisk Devices Recovering from Locked BlocksTftpxcpa27-1 disk0xcpa27-1 Router# configuration term Running HP Escon PA Diagnostic TestsConfiguring the HP Escon PA