Cisco Systems PA-4C-E 1 manual Laser Radiation

Page 19

Preparing for Installation

Class 1 laser products are not considered hazardous. The HP ESCON PA has embedded Class 3a laser LED assemblies operating at a nominal wavelength of 850 nanometer and a maximum potential output power of 1.25 milliwatts. The design of the HP ESCON PA incorporates engineering features including current limiting, which ensures that there is no human access to LED radiation greater than Class 1 under any set of operating, maintenance, or service conditions, including a single fault.

There are fewer than 0.442 milliwatts propagating in the link or in any portion of the module. Therefore, according to IEC825-2:1993, Hazard Level 1 prevails in all parts of the system.

The LEDs are located on the front face of the module.

Laser Radiation

Warning Laser radiation is present when the system is open. Statement 1009

Waarschuwing Laserstraling is aanwezig wanneer het systeem open is.

Varoitus Lasersäteitä järjestelmän ollessa avoinna.

Attention Production d'un rayonnement laser en position ouverte.

Warnung Laserstrahlung in geöffnetem Zustand.

Avvertenza Emissione di radiazioni laser quando il sistema è aperto.

Advarsel Laserstråling er til stede når enheten er åpen.

Aviso Radiação laser presente quando aberto.

¡Advertencia! Radiación láser presente cuando el sistema está abierto.

Varning! Laserstrålning pågår när enheten är öppen.

PA-4C-E 1-Port High-Performance ESCON Channel Port Adapter Installation and Configuration

 

OL-3743-02

19

 

 

 

Image 19
Contents PA-4C-E 1-Port High-Performance Document Version Date Change Summary Document Revision HistoryObjectives OrganizationRelated Documentation OL-3743-02 Port Adapter Overview OverviewCisco 7206 with an HP Escon PA in Port Adapter Slot Characteristic Escon Specification Escon SpecificationsLEDs Off Sequence Present Loaded Signal OnlinePort Adapter Slot Locations on the Supported Platforms Escon CablePort Adapter Slots in the Cisco 7206 Router Identifying Interface AddressesPlatform Interface Address Format Numbers Syntax HP Escon PA Microcode Overview Required Tools and EquipmentRouter# show microcode Hardware and Software RequirementsCisco IOS Release Image Names Checking Hardware and Software CompatibilitySafety Warnings Safety GuidelinesAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Spara Dessa Anvisningar Electrical Equipment Guidelines Laser LED Safety InformationPreventing Electrostatic Discharge Damage Laser Radiation Staring into Laser Beam Handling Port Adapters Removing and Installing Port AdaptersOnline Insertion and Removal Port Adapter Removal and Installation Step Attaching the HP Escon PA to the Channel Using the Exec Command Interpreter Configuring the HP Escon PAPerforming a Basic Interface Configuration Configuring the HP Escon PA InterfaceRouter# configure terminal Routerconfig-if#ip address 1.1.1.10 Checking the ConfigurationUsing show Commands to Verify the New Interface Status Routerconfig# interface channel 2/0Router# show version Using the show version or show hardware CommandsRouter# show controllers channel 2/0 Using the show controllers CommandsRouter# show interface channel 4/0 Using the show diag CommandRouter# ping Using the Ping Command to Verify Network ConnectivityHow Does HP Escon PA Microcode Ship? Upgrading Your HP Escon PA MicrocodeUpgrading the HP Escon PA Microcode from Cisco.com Router show flash Configuring the HP Escon PA MicrocodeRouterconfig# no microcode ecpa slot0xcpa28-1 Routerconfig# microcode ecpa slot0xcpa28-1Router# copy tftpxcpa28-6 slot0xcpa28-6 Using Flash MemoryRouter# cd slot0 Using Additional Flash Memory CommandsRouter# squeeze slot0 Recovering from Locked Blocks Using SanDisk DevicesTftpxcpa27-1 disk0xcpa27-1 Router# configuration term Running HP Escon PA Diagnostic TestsConfiguring the HP Escon PA