Cisco Systems Cisco AS5400XM Australia, Europe EU, Industry Canada Compliance

Page 56

Canada

Canada

The channelized T3 trunk card meets Canadian requirements for T3 support as specified in CP-01 standards.

Industry Canada Compliance

The following are notices required by Industry Canada Terminal Attachment Program Certification Procedure CP-01, Part I, Section 14.

Equipment Attachment Limitations

The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operational and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Australia

This customer equipment is to be installed and maintained by service personnel as defined by AS/NZ3260 clause 1.2.14.3 Service Personnel. Incorrect connection of connected equipment to the General Purpose Outlet could result in a hazardous situation.

Safety requirements are not fulfilled unless the equipment is connected to a wall socket outlet with protective earth contact.

Europe (EU)

This apparatus complies with EN55022 Class B and EN55024 standards when used as ITE/TTE equipment, and EN 300 386-2 (with EN55022 class B non-central office equipment) for Telecommunications Network Equipment (TNE).

The channelized E1 trunk card meets United Kingdom (UK) requirements for E1 support as specified in 607122 standards.

Regulatory Compliance and Safety Information for the Cisco AS5400 and Cisco AS5400XM Universal Gateways

56

OL-10264-01

 

 

Page 55 Page 57
Image 56
Page 55 Page 57
Contents This document contains the following sections Nebs Standards 56K StatementAgency Approvals Maintaining Safe Installation Distances Creepage Clearance Host or Expansion Card Vrms 1 or VDCTranslated Safety Warnings Statement 1-Power Disconnection WarningStatement 2-Disconnecting Telephone-Network Cables Statement 4-Power Supply Warning Statement 8-DC Power Connection Warning Statement 12-Power Supply Disconnection Warning Statement 13-Circuit Breaker 15A Warning Statement 14-Power Cord Warning Statement 19-TN Power Warning Statement 23-ISDN Connection Warning Translated Safety Warnings Statement 39-Grounded Equipment Warning Statement 43-Jewelry Removal Warning Statement 49-Qualified Personnel Warning Statement 61-Power Supply Wiring Warning Translated Safety Warnings Statement 77-Hazardous Voltages in WAN Ports Statement 87-Incorrect Connection Warning Statement 88-Service Personnel Warning Statement 89-Telecommunications Lines Warning Statement 90-Customer Equipment Warning Statement 96-Circuit Breaker 15A Warning Translated Safety Warnings Statement 140-Chassis Power Connection Statement 197-DC Power Supply Warning Translated Safety Warnings Statement 1001-Work During Lightning Activity Statement 1003-DC Power Disconnection Statement 1004-Installation Instructions Statement 1015-Battery Handling Translated Safety Warnings Statement 1017-Restricted Area Translated Safety Warnings Statement 1019-Main Disconnecting Device Statement 1021-SELV Circuit Statement 1022-Disconnect Device Translated Safety Warnings Statement 1023-No AWG Statement 1026-WAN Port Static Shock Statement 1040-Product Disposal Translated Safety Warnings Statement 1041-Disconnecting Telephone-Network Cables Statement 1046-Installing or Replacing the Unit OL-10264-01 Statement 1071-Warning Definition Bewaar Deze InstructiesBewahren SIE Diese Hinweise GUT AUF Spara Dessa Anvisningar GEM Disse Anvisninger Page Translated Safety Warnings United States FCC Rules, PartDIC SOC Cisco’s Supplier Declaration of Conformity Canada AustraliaEurope EU Industry Canada ComplianceE1 Dial Feature Card Independent of Host ScandinaviaJapan SingaporeClass a Notice for Canada MII China EMC Class a Notices and WarningsClass a Notice for FCC EMC Class a Notices and Warnings EMC Class B Notices and Warnings Class B Notice for FCCClass B Notice for Canada Statement 295-Class B Warning for KoreaRelated Documentation Obtaining DocumentationStatement 157-VCCI Compliance for Class B Equipment Cisco.comDocumentation DVD Ordering Documentation Documentation FeedbackCisco Product Security Overview Cisco Technical Support Website Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information Obtaining Additional Publications and Information OL-10264-01
Top Page Image Contents