Cisco Systems 3200 Series manual Cisco 3230 Router Card Stack, Wmic Mrpc Marc Smic Fesmic

Page 10

Chapter 1

Introduction

Cisco 3230 Rugged Enclosure

Cisco 3230 Router Card Stack

The Cisco 3230 Rugged Enclosure houses a router card stack bundle of up to (7) cards. Each bundle contains a base configuration of the following cards:

One Cisco 3230 Mobile Access Router Card (MARC)

One Cisco Serial Mobile Interface Card (SMIC)

One Cisco Fast Ethernet Switch Mobile Interface Card (FESMIC)

One Cisco Mobile Router Power Card (MRPC)

In addition, a card stack bundle can contain from one to three Cisco Wireless Mobile Interface Cards (WMICs).

The cards that make up a Cisco 3230 ISR card stack bundle are stacked in the order shown in Figure 1-3.

Figure 1-3 Cisco 3230 Router Card Stack Bundle

7

6

5

4

3

2

1

270443

1

WMIC 1

2

MRPC

 

 

 

 

3

MARC

4

SMIC

 

 

 

 

5

FESMIC

6

WMIC 2

 

 

 

 

7

WMIC 3

 

 

 

 

 

 

Cisco 3200 Series Router Hardware Upgrade Guide

1-4

OL-15983-01

 

 

Image 10
Contents Cisco 3200 Series Router Hardware Upgrade Guide Page Review Draft Cisco Confidential SFP Module Replacement Process About This Guide Obtaining Documentation and Submitting a Service Request Introduction Fully Assembled Cisco 3230 Rugged Enclosure Exploded View of the Cisco 3230 Rugged EnclosureExploded View of the 3230 Rugged Enclosure Cisco 3230 Router Card Stack Wmic Mrpc Marc Smic FesmicCisco 3270 Rugged ISR Fully Assembled Cisco 3270 Rugged EnclosureExploded View of the Cisco 3270 Rugged Enclosure 5shows an exploded view of the Cisco 3270 Rugged EnclosureCisco 3270 Router Card Stack Fesmic WmicWiring Cards What You Can Upgrade or Replace OL-15983-01 Replacing Cards in the Cisco 3230 ISR Rugged Enclosure Antenna End Cap Bolts Removing the Antenna End Cap Antenna End Cap Labels Removing the I/O End Cap I/O End Cap RemovalRemoving the Wiring Card Removing the Card StackReplacing or Adding a New Card Adding a New WmicReplacing a Wmic Routing the Antenna Cables Under the WmicFesmic and Smic Rotary Switches Replacing the FesmicReplacing the Marc Replacing the SmicReplacing the Mrpc Inserting the Card Stack into the Extrusion Wedge Lok Alignment10 Extrusion or Body of the Enclosure Reattaching the Wiring Card Attaching Version 1 of the Wiring CardAttaching the Version 2 of the Wiring Card 12 0- or 1-WMIC ConfigurationOn the wiring card Wiring card Reattaching the I/O End Cap 16 Cisco 3200 Rugged Enclosure Protective End Cap Cover Reattaching the Antenna End Cap Applying New I/O End Cap Function LabelsOL-15983-01 Replacing Cards in the Cisco ISR 3270 Rugged Enclosure Antenna End Cap Removal 270466 FE extender cable FE cable USB cable Power cable Removing the Wiring Card Carefully place the card stack on its side on a flat surface Inserting the Card Stack into the Enclosure LED and Serial Console Cables270471 Serial console cable LED cable Right alignment tab Tightening Wedge Loks 11 0-WMIC Configuration 12 1-WMIC Configuration 270478 Adjusting the Wmic Jumper Settings Wmic SettingsUSB 16 Attaching Antenna Labels Label OL-15983-01 Replacing the SFP Module SFP Module Replacement Process Replacing the SFP Module SFP Module Replacement Process OL-15983-01 D E IN-2