Cisco Systems 3200 Series Cisco 3270 Rugged ISR, Fully Assembled Cisco 3270 Rugged Enclosure

Page 11

Chapter 1 Introduction

Cisco 3230 Rugged Enclosure

Cisco 3270 Rugged ISR

The Cisco 3270 Rugged Enclosure is approximately double the size of the Cisco 3230 Rugged Enclosure. The larger enclosure is needed to accommodate the Cisco 3270 MARC, which is longer than the Cisco 3230 MARC and has greater port density, performance, fiber, and Gigabit Ethernet capabilities.

This section provides an overview of the Cisco 3270 Rugged Enclosure. For more information about it, see Cisco 3200 Series Router Hardware Reference.

Fully Assembled Cisco 3270 Rugged Enclosure

Figure 1-4shows two views of a fully assembled Cisco 3270 Rugged Enclosure.

Figure 1-4 Cisco 3270 Rugged Enclosure

270440

1

Front of the enclosure (I/O end cap)1

2

Back of the enclosure (antenna end cap)

1. This end cap shows four serial ports, but the typical configuration has two serial ports.

Cisco 3200 Series Router Hardware Upgrade Guide

 

OL-15983-01

1-5

 

 

 

Image 11
Contents Cisco 3200 Series Router Hardware Upgrade Guide Page Review Draft Cisco Confidential SFP Module Replacement Process About This Guide Obtaining Documentation and Submitting a Service Request Introduction Exploded View of the Cisco 3230 Rugged Enclosure Fully Assembled Cisco 3230 Rugged EnclosureExploded View of the 3230 Rugged Enclosure Wmic Mrpc Marc Smic Fesmic Cisco 3230 Router Card StackFully Assembled Cisco 3270 Rugged Enclosure Cisco 3270 Rugged ISR5shows an exploded view of the Cisco 3270 Rugged Enclosure Exploded View of the Cisco 3270 Rugged EnclosureFesmic Wmic Cisco 3270 Router Card StackWiring Cards What You Can Upgrade or Replace OL-15983-01 Replacing Cards in the Cisco 3230 ISR Rugged Enclosure Antenna End Cap Bolts Removing the Antenna End Cap Antenna End Cap Labels I/O End Cap Removal Removing the I/O End CapRemoving the Card Stack Removing the Wiring CardAdding a New Wmic Replacing or Adding a New CardRouting the Antenna Cables Under the Wmic Replacing a WmicReplacing the Fesmic Fesmic and Smic Rotary SwitchesReplacing the Mrpc Replacing the SmicReplacing the Marc Wedge Lok Alignment Inserting the Card Stack into the Extrusion10 Extrusion or Body of the Enclosure Attaching Version 1 of the Wiring Card Reattaching the Wiring Card12 0- or 1-WMIC Configuration Attaching the Version 2 of the Wiring CardOn the wiring card Wiring card Reattaching the I/O End Cap 16 Cisco 3200 Rugged Enclosure Protective End Cap Cover Applying New I/O End Cap Function Labels Reattaching the Antenna End CapOL-15983-01 Replacing Cards in the Cisco ISR 3270 Rugged Enclosure Antenna End Cap Removal 270466 FE extender cable FE cable USB cable Power cable Removing the Wiring Card Carefully place the card stack on its side on a flat surface LED and Serial Console Cables Inserting the Card Stack into the Enclosure270471 Serial console cable LED cable Right alignment tab Tightening Wedge Loks 11 0-WMIC Configuration 12 1-WMIC Configuration 270478 Wmic Settings Adjusting the Wmic Jumper SettingsUSB 16 Attaching Antenna Labels Label OL-15983-01 Replacing the SFP Module SFP Module Replacement Process Replacing the SFP Module SFP Module Replacement Process OL-15983-01 D E IN-2