Cisco Systems 3200 Series manual Inserting the Card Stack into the Extrusion, Wedge Lok Alignment

Page 27

Chapter 2 Replacing Cards in the Cisco 3230 ISR Rugged Enclosure

Card Replacement Process

Inserting the Card Stack into the Extrusion

To insert the card stack into the extrusion, follow these steps:

Step 1 Make sure that the LED cable is connected to the FESMIC.

Step 2 Route the FESMIC LED cable over the top of the stack.

Step 3 Align each card’s Wedge Loks so that the angles on the Wedge Loks match the angle of the Wedge Lok rail. Figure 2-9shows proper Wedge Lok alignment.

Figure 2-9 Wedge Lok Alignment

2 1

1

127880

1

Wedge Lok alignment

2

Wedge Lok rail

Step 4 Place the extrusion on a sturdy, flat surface with the I/O end cap side facing up.

		Cisco 3200 Series Router Hardware Upgrade Guide
		Cisco 3200 Series Router Hardware Upgrade Guide
	OL-15983-01			2-11
	OL-15983-01			2-11

Image 27

Contents Cisco 3200 Series Router Hardware Upgrade Guide Page Review Draft Cisco Confidential SFP Module Replacement Process About This Guide Obtaining Documentation and Submitting a Service Request Introduction Exploded View of the Cisco 3230 Rugged Enclosure Fully Assembled Cisco 3230 Rugged EnclosureExploded View of the 3230 Rugged Enclosure Wmic Mrpc Marc Smic Fesmic Cisco 3230 Router Card StackFully Assembled Cisco 3270 Rugged Enclosure Cisco 3270 Rugged ISR5shows an exploded view of the Cisco 3270 Rugged Enclosure Exploded View of the Cisco 3270 Rugged EnclosureFesmic Wmic Cisco 3270 Router Card StackWiring Cards What You Can Upgrade or Replace OL-15983-01 Replacing Cards in the Cisco 3230 ISR Rugged Enclosure Antenna End Cap Bolts Removing the Antenna End Cap Antenna End Cap Labels I/O End Cap Removal Removing the I/O End CapRemoving the Card Stack Removing the Wiring CardAdding a New Wmic Replacing or Adding a New CardRouting the Antenna Cables Under the Wmic Replacing a WmicReplacing the Fesmic Fesmic and Smic Rotary SwitchesReplacing the Smic Replacing the MarcReplacing the Mrpc Wedge Lok Alignment Inserting the Card Stack into the Extrusion10 Extrusion or Body of the Enclosure Attaching Version 1 of the Wiring Card Reattaching the Wiring Card12 0- or 1-WMIC Configuration Attaching the Version 2 of the Wiring CardOn the wiring card Wiring card Reattaching the I/O End Cap 16 Cisco 3200 Rugged Enclosure Protective End Cap Cover Applying New I/O End Cap Function Labels Reattaching the Antenna End CapOL-15983-01 Replacing Cards in the Cisco ISR 3270 Rugged Enclosure Antenna End Cap Removal 270466 FE extender cable FE cable USB cable Power cable Removing the Wiring Card Carefully place the card stack on its side on a flat surface LED and Serial Console Cables Inserting the Card Stack into the Enclosure270471 Serial console cable LED cable Right alignment tab Tightening Wedge Loks 11 0-WMIC Configuration 12 1-WMIC Configuration 270478 Wmic Settings Adjusting the Wmic Jumper SettingsUSB 16 Attaching Antenna Labels Label OL-15983-01 Replacing the SFP Module SFP Module Replacement Process Replacing the SFP Module SFP Module Replacement Process OL-15983-01 D E IN-2