Cisco Systems 3200 Series manual Replacing the SFP Module SFP Module Replacement Process

Page 57

Chapter 4 Replacing the SFP Module

SFP Module Replacement Process

Step 9 Grasp the SFP module between your thumb and index finger, and carefully remove it from the module slot.

Step 10 Place the removed SFP module in an antistatic bag or other protective environment.

Caution Do not remove the rubber plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light.

Step 11 Find the send (TX) and receive (RX) markings that identify the top side of the replacement SFP module.

Note On some SFP modules, the send (TX) and receive (RX) markings might be replaced by arrows that show the direction of the connection, either send or receive (TX or RX).

Step 12 Align the SFP module in front of the slot opening.

Step 13 Insert the SFP module into the slot until you feel the connector on the module snap into place in the back of the slot.

Step 14 Remove the dust plugs from the SFP module optical ports. Store the plugs for later use.

Caution Do not remove the dust plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light.

Step 15 Clean the fiber-optic connectors by using standard procedures.

Step 16 Insert the LC cable connector into the SFP module.

Step 17 Verify that the gasket is in place and replace the antenna end cap by using a 3/8-inch socket wrench to remove the bolts, torquing the bolts to 58 to 68 in-lb.

For more information about replacing SFP modules and diagnosing their problems, see Cisco 3200 Series Router Hardware Reference Guide.

Cisco 3200 Series Router Hardware Upgrade Guide

 

OL-15983-01

4-3

 

 

 

Image 57
Contents Cisco 3200 Series Router Hardware Upgrade Guide Page Review Draft Cisco Confidential SFP Module Replacement Process About This Guide Obtaining Documentation and Submitting a Service Request Introduction Exploded View of the Cisco 3230 Rugged Enclosure Fully Assembled Cisco 3230 Rugged EnclosureExploded View of the 3230 Rugged Enclosure Wmic Mrpc Marc Smic Fesmic Cisco 3230 Router Card StackFully Assembled Cisco 3270 Rugged Enclosure Cisco 3270 Rugged ISR5shows an exploded view of the Cisco 3270 Rugged Enclosure Exploded View of the Cisco 3270 Rugged EnclosureFesmic Wmic Cisco 3270 Router Card StackWiring Cards What You Can Upgrade or Replace OL-15983-01 Replacing Cards in the Cisco 3230 ISR Rugged Enclosure Antenna End Cap Bolts Removing the Antenna End Cap Antenna End Cap Labels I/O End Cap Removal Removing the I/O End CapRemoving the Card Stack Removing the Wiring CardAdding a New Wmic Replacing or Adding a New CardRouting the Antenna Cables Under the Wmic Replacing a WmicReplacing the Fesmic Fesmic and Smic Rotary SwitchesReplacing the Smic Replacing the MarcReplacing the Mrpc Wedge Lok Alignment Inserting the Card Stack into the Extrusion10 Extrusion or Body of the Enclosure Attaching Version 1 of the Wiring Card Reattaching the Wiring Card12 0- or 1-WMIC Configuration Attaching the Version 2 of the Wiring CardOn the wiring card Wiring card Reattaching the I/O End Cap 16 Cisco 3200 Rugged Enclosure Protective End Cap Cover Applying New I/O End Cap Function Labels Reattaching the Antenna End CapOL-15983-01 Replacing Cards in the Cisco ISR 3270 Rugged Enclosure Antenna End Cap Removal 270466 FE extender cable FE cable USB cable Power cable Removing the Wiring Card Carefully place the card stack on its side on a flat surface LED and Serial Console Cables Inserting the Card Stack into the Enclosure270471 Serial console cable LED cable Right alignment tab Tightening Wedge Loks 11 0-WMIC Configuration 12 1-WMIC Configuration 270478 Wmic Settings Adjusting the Wmic Jumper SettingsUSB 16 Attaching Antenna Labels Label OL-15983-01 Replacing the SFP Module SFP Module Replacement Process Replacing the SFP Module SFP Module Replacement Process OL-15983-01 D E IN-2