Cisco Systems manual Routing IP with a Cisco 700 Series Router to an ISP

Page 31

across the ISDN line. In a bridging scenario, the router does not need an IP address and bridging occurs regardless. The IP address is used when the router is being managed remotely by a Telnet session or participating in SNMP.

Both sides of the WAN must be configured with PPP host names, secrets, and passwords for authentication. Each profile must also include dialing information.

Cisco 700 Series Router Bridging Instructions

The IP address and subnet mask are not entered. IP address assignments are not necessary in a bridged network; they are used only if the router is being pinged or accessed through Telnet or SNMP.

Following is the command summary for configuring the Cisco 700 series router to bridge to the router called central at the central site:

set system CPA765 set user central set active

set ppp secret client set ppp password client set bridging on

set 1 number phone_number set 2 number phone_number reboot

Routing IP with a Cisco 700 Series Router to an ISP

This section describes how to configure a Cisco 700 series router to route to an ISP by using Internet Protocol (IP). Figure 3-2 illustrates the configuration used in this example. By default, PPP incoming authentication is on and outgoing authentication is off.

Note If you are connecting to an Ascend device, you must disable PPP Bandwidth Allocation Control Protocol (BACP) and PPP multilink.

Basic Configurations 3-9

Image 31
Contents Cisco 700 Series Router Configuration Guide Page N T E N T S Chapter Using Chap Chapter Configuring Dhcp Relay, Dhcp Server, and PAT Token Caching A-2 About This Manual Related Documentation Conventions Set systemname systemname Supported Protocols OverviewSoftware Images Administrative Configuration Options 4Cisco700 Series Router Command Reference Profile Overview Using Profiles with Cisco 700 Series RoutersProfiles and Connections System and Profile ParametersProfile Mode Parameter Set System Mode Parameter SetPermanent Profiles Lists the parameters that can be configured in a profileHost set user tomd Displaying Profile ConfigurationsCreating and Modifying Profiles Removing Profile-Based ValuesChanging Profile Names HostProfile reset user tomdIncoming Calls Deleting ProfilesOutgoing Calls 8Cisco700 Series Router Configuration Guide Basic Configuration Concepts Basic ConfigurationsProfiles Bridges and RoutersLANs and WANs Show config Current ConfigurationRemote and Central Sites Host show configSet def Password and SecretStarting Point Additional ReferenceSet autodetection on Setting Spid Autodetection North America onlySet switch dms Setting SPIDs Manually North America onlyBridging Example Bridging with a Cisco 700 Series RouterCisco 700 Series Router Bridging Instructions Routing IP with a Cisco 700 Series Router to an ISPConnecting to an ISP-Example Configuration Set user isp Set number Routing IP to a Central SiteRouting a Cisco 700 Series Router to an ISP Instructions Set system 764 cd lan Set ip addressRouting IP to a Central Site-Example Configuration Set system remote765 set multidestination on cd LAN Central Site IP Routing Command SummarySet ppp auth in chap set ppp secret host cd lan Routing IP and IPX On-DemandRouting IP and IPX On-Demand-Example Configuration Cd LAN On-Demand IP and IPX Routing with PPP InstructionsSet bridging off Central Site On-Demand IP and IPX Routing with PPP Commands18Cisco 700 Series Router Configuration Guide Using Chap Spid Detection North America only IP Static Routing and Callback with Chap AuthenticationSet ip rip version 2 set user Remote Cisco 765 Command SummarySet switch 5ess Set ip rip update off set timeoutIP Static Routing with Chap Authentication and MLP Demand 2 threshold 32 duration 5 set active Reboot Set ip rip update periodic set user Set ppp secret clientIP Static Routing with PAP Authentication IP Static Routing with PAP Authentication and MLPSet bridging off set timeout 360 set active reboot IP Unnumbered Static Routing and Chap with MLP IP Unnumbered Routing and Chap Authentication with MLPSet ppp secret host cd lan IP Static and IPX Static Routing with PPP IP Static and IPX Static Routing with Chap and MLPSet multidestination on Set ip rip update periodic set user4500 IPX Static Routing with Chap and MLPSet ipx rip update periodic set user Dynamic Routing Protocols Multilink PPP EncapsulationSet ppp multilink off Bridging to a Router Running Cisco IOS Software 16Cisco700 Series Router Configuration Guide Configuring Dhcp Relay, Dhcp Server, and PAT Dhcp Server Application Notes Dhcp DescriptionDhcp Relay Application Notes PAT DescriptionPAT Application Notes Ipcp Address Negotiation Application Notes Ipcp DescriptionSet ip framing none PPP Ipcp Negotiation Example Cisco 765 Series Router CommandsDhcp Relay with Ipcp Negotiation Example Verify the ConfigurationSet system Dhcp Server with Ipcp Negotiation Example Set dhcp gateway primary 172.168.1.1 cd lan Set dhcp serverSet user PAT with Ipcp Single-Destination Negotiation PAT with Ipcp Single-Destination Negotiation ExampleSet system Set ip pat po ftp 10.0.0.2 cd lan Dhcp Server with PAT and Ipcp Single-Destination Negotiation Set active Dhcp server Cisco Isdn network Set ip netmask 255.255.255.0 set ip pat on Verify the Configuration 16Cisco700 Series Router Configuration Guide Configuring Remote Capi Capi and RVS-COM Supported D-Channel Protocols Remote Capi Router CommandsSupported Applications Rcapi Command Summary Configuring the Cisco 700 Router as an Rcapi ServerSet rcapi on Set dir Local-router show rcapi status 6Cisco700 Series Router Configuration Guide Token Card and Cisco Secure Authentication Support Token Caching Figure A-2 PAP Client Packet 4Cisco700 Series Router Configuration Guide D E ISP Ipxcp RIP ARP BCP Chap Dhcp Icmp Ipcp Ipxcp ISDN-DCP Mlppp PAP PAT
Related manuals
Manual 8 pages 18.06 Kb