Cisco Systems 700 manual Ipcp Description, Ipcp Address Negotiation Application Notes

Page 60

IPCP Description

IPCP Description

If you are using IP routing, Cisco 700 series routers must be configured for IPCP to connect to routers running Cisco IOS software. Use the set ip framing command in profile mode to enable IPCP for user-defined WAN profiles by setting IP framing to none.

The following example illustrates IPCP enabled by disabling IP framing:

766:2503> set ip framing none

Note Do not set the ip framing or the ipx framing commands to none when configuring the permanent LAN profile.

IPCP Address Negotiation Application Notes

The following are application notes for IPCP address negotiation:

•Cisco 700 series routers require a user-defined profile, configured with IP routing on, to receive an IPCP addresses.

•A router running Cisco IOS software must be configured to hand off IPCP addresses.

•If a manually configured IP address exists on the Internal profile of a Cisco 700 series router, the IPCP address is assigned to the WAN profile.

•If a manually configured IP address exists on the LAN profile, the IPCP address is assigned to the Internal profile.

5-4Cisco700 Series Router Configuration Guide

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Cisco 700 Series Router Configuration Guide Page N T E N T S Chapter Using Chap Chapter Configuring Dhcp Relay, Dhcp Server, and PAT Token Caching A-2 About This Manual Related Documentation Conventions Set systemname systemname Overview Supported ProtocolsSoftware Images Administrative Configuration Options 4Cisco700 Series Router Command Reference Using Profiles with Cisco 700 Series Routers Profile OverviewSystem and Profile Parameters Profiles and ConnectionsSystem Mode Parameter Set Profile Mode Parameter SetLists the parameters that can be configured in a profile Permanent ProfilesDisplaying Profile Configurations Creating and Modifying ProfilesRemoving Profile-Based Values Host set user tomdHostProfile reset user tomd Incoming CallsDeleting Profiles Changing Profile NamesOutgoing Calls 8Cisco700 Series Router Configuration Guide Basic Configurations Basic Configuration ConceptsBridges and Routers ProfilesLANs and WANs Current Configuration Show configHost show config Remote and Central SitesPassword and Secret Starting PointAdditional Reference Set defSetting Spid Autodetection North America only Set autodetection onSetting SPIDs Manually North America only Set switch dmsBridging with a Cisco 700 Series Router Bridging ExampleRouting IP with a Cisco 700 Series Router to an ISP Cisco 700 Series Router Bridging InstructionsConnecting to an ISP-Example Configuration Routing IP to a Central Site Routing a Cisco 700 Series Router to an ISP InstructionsSet system 764 cd lan Set ip address Set user isp Set numberRouting IP to a Central Site-Example Configuration Central Site IP Routing Command Summary Set system remote765 set multidestination on cd LANRouting IP and IPX On-Demand Set ppp auth in chap set ppp secret host cd lanRouting IP and IPX On-Demand-Example Configuration On-Demand IP and IPX Routing with PPP Instructions Cd LANCentral Site On-Demand IP and IPX Routing with PPP Commands Set bridging off18Cisco 700 Series Router Configuration Guide Using Chap IP Static Routing and Callback with Chap Authentication Spid Detection North America onlyRemote Cisco 765 Command Summary Set switch 5essSet ip rip update off set timeout Set ip rip version 2 set userIP Static Routing with Chap Authentication and MLP Set ip rip update periodic set user Set ppp secret client Demand 2 threshold 32 duration 5 set active RebootIP Static Routing with PAP Authentication and MLP IP Static Routing with PAP AuthenticationSet bridging off set timeout 360 set active reboot IP Unnumbered Routing and Chap Authentication with MLP IP Unnumbered Static Routing and Chap with MLPSet ppp secret host cd lan IP Static and IPX Static Routing with Chap and MLP IP Static and IPX Static Routing with PPPSet ip rip update periodic set user Set multidestination onIPX Static Routing with Chap and MLP 4500Set ipx rip update periodic set user Multilink PPP Encapsulation Dynamic Routing ProtocolsSet ppp multilink off Bridging to a Router Running Cisco IOS Software 16Cisco700 Series Router Configuration Guide Configuring Dhcp Relay, Dhcp Server, and PAT Dhcp Description Dhcp Server Application NotesPAT Description Dhcp Relay Application NotesPAT Application Notes Ipcp Description Ipcp Address Negotiation Application NotesSet ip framing none Cisco 765 Series Router Commands PPP Ipcp Negotiation ExampleVerify the Configuration Dhcp Relay with Ipcp Negotiation ExampleSet system Dhcp Server with Ipcp Negotiation Example Set dhcp server Set dhcp gateway primary 172.168.1.1 cd lanSet user PAT with Ipcp Single-Destination Negotiation Example PAT with Ipcp Single-Destination NegotiationSet system Set ip pat po ftp 10.0.0.2 cd lan Dhcp Server with PAT and Ipcp Single-Destination Negotiation Set active Dhcp server Cisco Isdn network Set ip netmask 255.255.255.0 set ip pat on Verify the Configuration 16Cisco700 Series Router Configuration Guide Configuring Remote Capi Capi and RVS-COM Remote Capi Router Commands Supported D-Channel ProtocolsSupported Applications Configuring the Cisco 700 Router as an Rcapi Server Rcapi Command SummarySet rcapi on Set dir Local-router show rcapi status 6Cisco700 Series Router Configuration Guide Token Card and Cisco Secure Authentication Support Token Caching Figure A-2 PAP Client Packet 4Cisco700 Series Router Configuration Guide D E ISP Ipxcp RIP ARP BCP Chap Dhcp Icmp Ipcp Ipxcp ISDN-DCP Mlppp PAP PAT
Related manuals
Manual 8 pages 18.06 Kb
Top Page Image Contents