Cisco Systems OL-7870-02 manual Telecom Approvals Listing, FCC Part 68 Notice

Page 59

Telecom Approvals Listing

Telecom Approvals Listing

The Cisco MWR 1941-DC-A router meets the requirements listed in this section for telecommunications equipment.

FCC Part 68 Notice

This equipment complies with Part 68 of the FCC rules. A label on the bottom of the chassis contains the FCC registration number in the format US:5BIDDNAN0006. If requested, this information must be provided to the telephone company.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify you as soon as possible. You will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that might affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications to maintain uninterrupted service.

If you experience trouble with this equipment, please contact Cisco Systems for repair and warranty information. If the problem is causing harm to the telephone network, the telephone company might request that you remove the equipment from the network until the problem is resolved. All repairs should be handled by authorized Cisco Systems service personnel.

Normally, this equipment will be used in conjunction with FCC-approved equipment that limits the Encoded Analog Content that provides the required Billing Protection.

The facility interface and service order codes are shown in Table 3.

Table 3

Cisco MWR 1941-DC-A Router VWIC-2T1/E1-RAN Interface Card Facility Interface and

 

Service Order Codes

 

 

 

 

 

 

 

Model Name

 

Facility Interface Code

Service Order Code

Jack Type

 

 

 

 

VWIC-2T1/E1-RAN

04DU9.BN, 04DU9.DN,

6.0Y

RJ48C

 

 

04DU9.1KN, 04DU9.1SN

 

 

 

 

 

 

 

Cisco MWR 1941-DC-A routers (bearing labeling identification number (US:5B1DDNAN0165) comply with the following requirements:

•FCC Rules and Regulations 47 CFR Part 68

•TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network, July 2001, as adopted by the Administrative Council on Terminal Attachments (ACTA)

Cisco Regulatory Compliance and Safety Information for the Cisco MWR 1941-DC-A Mobile Wireless Edge Router

 

OL-7870-02

59

 

 

 

Page 58 Page 60
Image 59
Page 58 Page 60
Contents November 8 Revision Date Change Summary Document Revision HistoryTranslated Safety Warnings Statement 4-Power Supply Warning Translated Safety Warnings Statement 12-Power Supply Disconnection Warning Statement 8-DC Power Connection WarningTranslated Safety Warnings Statement 1064-Grounded Equipment Warning Statement 38-Power Cabling WarningStatement 43-Jewelry Removal Warning Translated Safety Warnings Statement 122-Exposed DC Power Wire Warning Statement 1001-Work During Lightning Activity Statement 1002-DC Power Supply Statement 1003-DC Power Disconnection Statement 1004-Installation Instructions 10A minimum, 60VDC Statement 1005-Circuit Breaker10A minimum, 60VDC Translated Safety Warnings Translated Safety Warnings Statement 1007-TN and IT Power Systems Statement 1017-Restricted Area Statement 1018-Supply Circuit Warning Bewaar Deze Instructies Statement 1071-Warning DefinitionConservez CES Informations Guarde Estas Instrucciones Statement 1021-SELV Circuit Translated Safety Warnings Statement 1023-No AWG Statement 1024-Ground Conductor Statement 1025-Use Copper Conductors Only Statement 1026-WAN Port Static Shock Statement 1029-Blank Faceplates and Cover Panels Translated Safety Warnings Statement 1030-Equipment Installation Veroorzaken of schade aan de eenheid Statement 1031-EU Public Network PortStatement 1033-SELV-IEC 60950 DC Power Supply Statement 1035-Proximity to Water Statement 1036-Telephone Jacks in Wet Locations Statement 1037-Uninsulated Wires and Terminals Statement 1040-Product Disposal Statement 1041-Disconnecting Telephone-Network Cables Statement 1043-Installation Hazard Translated Safety Warnings Statement 1045-Short-circuit Protection Statement 1046-Installing or Replacing the Unit Statement 1047-Overheating Prevention Statement 1048-Rack Stabilization Statement 1049-Rack Installation Statement 1058-Power and Relay Connector Translated Safety Warnings Translated Safety Warnings Statement 1065-Console Cable Connection Translated Safety Warnings OL-7870-02 European Directive Regulatory Standards Compliance Specification DescriptionEMC Environmental Conditions EMC Class a Statements/WarningsJapan Vcci Class a FCC Class aCanada Class a International Cispr 22 Class aFCC Part 68 Notice Telecom Approvals ListingCanada CS-03 Certification Japan Jate CertificationDocumentation DVD Obtaining DocumentationNew Zealand- PTC-217 Approval Cisco.comOrdering Documentation Documentation FeedbackCisco Product Security Overview Cisco Technical Support Website Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Copyright 2005, Cisco Systems, Inc
Top Page Image Contents