Cisco Systems 78-16356-01 manual Preparing for Installation Safety

Page 34

Chapter 2 Preparing for Installation

Safety

Warning This unit might have more than one power cord. To reduce the risk of electrical shock, disconnect all power supply cords before servicing the unit. Statement 106

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning This equipment is intended to be grounded to comply with emission and immunity requirements. Ensure that the switch functional ground lug is connected to earth ground during normal use. Statement 1064

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001.

Warning The power supply circuitry for the equipment can constitute an energy hazard. Before you install or replace the equipment, remove all jewelry (including rings, necklaces, and watches). Metal objects can come into contact with exposed power supply wiring or circuitry inside the DSLAM equipment. This could cause the metal objects to heat up and cause serious burns or weld the metal object to the equipment. Statement 207

 

Cisco Global Site Selector 4491 Hardware Installation Guide

2-4

78-16356-01

Image 34
Contents Cisco Global Site Selector 4491 Hardware Installation Guide Page Cisco Global Site Selector 4491 Hardware Installation Guide Page N T E N T S Installing the GSS Maintaining Your GSS Cabling a Modem to the GSS B-4 Figure B-1 Page Port Specifications A-3 Xii Preface Audience How to Use This Guide Chapter/Appendix DescriptionRelated Documentation Document Title ProvidesSymbols and Conventions XviiBewaar Deze Instructies Varoitus Tärkeitä TurvallisuusohjeitaWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaTA Vare PÅ Disse Instruksjonene Aviso Instruções Importantes DE SegurançaVarning! Viktiga Säkerhetsanvisningar Spara Dessa AnvisningarXxii Introduction IntroductionSystem Hardware Features Front Panel Features Rear Panel FeaturesFront Panel Features Front Panel ViewIndicator Color State Indicates LED IndicatorsRear Panel Features Rear Panel ViewPorts and Connectors Console PortParameters Settings Pin Signal DefinitionShell Ethernet Connectors Ethernet Port 0 Pin NumbersPreparing for Installation Safety Preparing for Installation Safety Preparing for Installation Safety Preparing for Installation Safety General Precautions Maintaining Safety with ElectricityProtecting Against Electrostatic Discharge Preparing Your Site for Installation Choosing a Site for Installation EnvironmentalEnsuring Overcurrent Protection AC PowerGrounding the GSS Creating a Safe Environment Precautions for Rack-Mounting CablingRequired Tools and Equipment Installing the GSS Unpacking and Inspecting the GSS If the Product is DamagedInstalling Your GSS Installing the GSS in a Four-PostRack Rack Rail Components Attaching the Telescopic Rails to the Rack Assembly Telescoping the Rail Attaching Front Rail to the Right Side of the Rack Telescopic Rail Adjustment Screws Attaching Back Rail to the Right Side of the Rack Inserting the GSS into the Rack Attaching a Two-Post Rack Bracket to the GSS Sliding the GSS into the Four-post RackAttaching the Right Bracket to the Right Side of the GSS Installing the GSS on a Workbench or Tabletop Connecting Cables 10 GSS Back Panel Ports and ConnectorsConnecting AC Power Booting the GSS Establishing a Serial Console Connection Checking the Front Panel LEDs 11 GSS 4491 Front Panel LEDsRemoving or Replacing a GSS Installing the GSS Removing or Replacing a GSS Installing the GSS Removing or Replacing a GSS Troubleshooting the GSS Hardware Checking the BasicsChecking Connections Troubleshooting the GSS Hardware Checking Connections Troubleshooting the GSS Hardware Checking Connections Maintaining Your GSS Maintaining Your Site EnvironmentTemperature Humidity AltitudeCorrosion Dust and ParticlesElectrostatic Discharge Electromagnetic and Radio Frequency Interference Power Source Interruptions MagnetismUsing Power Protection Devices Surge ProtectorsUninterruptible Power Supplies Line ConditionersElectrical Specifications AC Specification OperationalEnvironmental Specifications Specification Operational Non-operationalPort Specifications Physical SpecificationsDescription Specification Appendix a Specifications Port Specifications Connecting a Modem to the GSS Console Port Configuring a Modem Table B-1connector pinouts for the GSS console portTable B-1 Console Port Connector Pinouts Figure B-2 Rear Panel Ports and Connectors Cabling a Modem to the GSSParameters Default Settings 78-16356-01 D E IN-2 IN-3 IN-4 IN-5 IN-6