Cabletron Systems 9H532-24, 9H531-24, 9H533-24 manual FCC Notice

Page 3

Notice

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Cabletron Systems, Inc.

35 Industrial Way

Rochester, NH 03867

1999 by Cabletron Systems, Inc. All Rights Reserved

Printed in the United States of America

Order Number: 9033050-02

Cabletron Systems, LANVIEW, and MicroMMAC are registered trademarks and SmartSwitch is a trademark of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.

WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INDUSTRY CANADA NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

VCCI NOTICE

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

i

Image 3
Contents 9033050-02 Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Iii Cabletron Systems Limited Program License Agreement Page Page Declaration of Conformity Viii Contents Contents Introduction FeaturesIntroduction Auto-Negotiation Management Broadcast Suppression Priority Indicator Transmit Queue Switching Options Related Manuals Introduction Unpacking the Module User Accessible ComponentsInstalling the SmartSwitch 9000 Module Switch Function Description Using DIP Switch Installing the Module into the SmartSwitch 9000 ChassisInstalling the Module Reset Switch Reset Switch100BASE-FX Network Cabling Requirements10BASE-T Network 100BASE-TX NetworkInstalling the SmartSwitch 9000 Module Technical Overview SmartSwitch ArchitectureTechnical Overview System Management BusesSystem Diagnostic Controller SMB-1 BusSMB-10 Bus DC/DC Converter INB InterfaceI960 Core Lanview LEDs LED Mode SwitchLanview LEDs Functions of the INB transmit LED are listed in Table Functions of the INB receive LED are listed in Table DPX Status LEDs 9H532-24 only Lanview LEDs Technical Specifications SpecificationsService Regulatory CompliancePhysical