Cabletron Systems SEHI-24, SEHI-22, SEHI-32, SEHI-34 manual Introduction Getting Help, Sehi Overview

Page 10

INTRODUCTION

1.2GETTING HELP

If you need additional support related to the Cabletron Systems SEHI, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support:

By phone	(603) 332-9400
	Monday-Friday; 8am - 8pm EST
By CompuServe® ..... GO CTRON from any ! prompt
By Internet mail	support@ctron.com
By FTP	ctron.com (134.141.197.25)
	Login: anonymous, Password: your email address

1.3SEHI OVERVIEW

The 10BASE-T SEHI is an intelligent repeating hub that provides front panel ports for network connections and a rear panel HubSTACK Interconnect Bus port for stackable connections. The SEHI is designed to manage Cabletron Systems’ SEH series of non-intelligent stackable hubs.

HubSTACK 10BASE-T HUB WITH LANVIEW®	EPIM-2
SEHI-24

RESET

COM

RCV

LNK

E

24 23 22 21 20 19 18 17 16 15 14 13

2

24X

23X

22X

21X

20X

19X

18X

17X

16X

15X

14X

13X

PWR

CPU

RCV

CLN

LNK

E

12 11 10 9 8 7

6

5

4

3

2

1

1

12X

11X

10X

9X

8X

7X

6X

5X

4X

3X

2X

1X

EPIM-1

SEHI-2410BASE-T HUB WITH LANVIEW®

SEH INTERCONNECT

OUT

HubSTACK 10BASE-T HUB WITH LANVIEW®	EPIM-2
SEHI-34

RESET

COM

	RCV
	LNK							E
	24 23 22 21 20 19 18 17 16 15 14 13							2
PWR
CPU	RCV
CLN	LNK							E
	12 11 10 9 8 7	6	5	4	3	2	1	1

24X

13X

12X

1X

EPIM-1

SEHI-3410BASE-T HUB WITH LANVIEW®

SEH INTERCONNECT

OUT

Figure 1-1. The SEHI-24 and SEHI-34

Page 1-2

Image 10

Contents 10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper FCC Notice DOC NoticeCabletron SYSTEMS, INC Program License Agreement Cabletron Software Program LicenseExclusion of Warranty Disclaimer of Liability United States Government Restricted RightsTable of Contents Troubleshooting InstallationConnecting to the Network Local ManagementContents Appendix B Twisted Pair Wiring Tables A-1 Using this Manual Chapter IntroductionIntroduction Getting Help Sehi OverviewPolarity Detection and Correction Sehi FeaturesRepeater Functionality Flash EEPROMsLocal Management Reset ButtonLanview LEDs Stackable CapabilitiesIntroduction Optional Features EpimRack Mount or Wall Mount Hardware Daughter Board Upgrade KitRelated Manuals Cable Specifications HubSTACK Interconnect Cable RequirementsImpedance LengthInsertion Loss JitterCrosstalk DelayTemperature NoiseFiber Optic Budget and Propagation Delay Cable Type Attenuation Maximum Cable LengthInstallation REQUIREMENTS/SPECIFICATIONS Cable Type ConnectorsThin-Net Network Requirements for the EPIM-C Module TerminatorsAUI Cable Requirements for the EPIM-A and EPIM-X Modules Network Port SpecificationsAUI Cable SEHI-22 and SEHI-24 Network Port Speciﬁcations SEHI-32 and SEHI-34 Network Port SpeciﬁcationsPin Champ Connector Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications EPIM-TEPIM-F1 and EPIM-F2 Parameter Typical Worst Worst Case Typical Value BudgetEPIM-F3 EPIM-F3Parameter Typical Minimum Maximum Connector Type EPIM-CEPIM-A and EPIM-X AUI Port EPIM-A and EPIM-XCOM Transceiver RequirementsGeneral Delay Times Start of PacketsDelay Times JAM PreambleOutput Min. Load Max. Load Max Power Fault ProtectionPower Supply Requirements JAM OutputSafety PhysicalInstalling the Sehi Unpacking the SehiStacking the Sehi Stacking the Sehi Attaching the Strain Relief Bracket Disconnect SEH and Sehi Interconnect Cables At the OUT PortInstalling the Sehi in the Rack Rack Mounting the SehiWall Mounting the Sehi Free-Standing Installation Shelf or Table-top InstallationInstallation Connecting the Sehi to the Power Source Connecting the Sehi to the Network Connecting to Network Ports, SEHI-22 and SEHI-24EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 Connecting a UTP Segment to an EPIM-T EPIM-T Cross-over SwitchConnecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C Connecting an AUI Cable to an EPIM-A EPIM-AConnecting an AUI Cable to an EPIM-X Finishing the Installation On Position Toward Back Epim OFF Position Toward FrontChapter Troubleshooting Installation CHECK-OUTUsing Lanview PWR CPURCV Troubleshooting CLNUsing the Reset Button LNKChapter Local Management Local Management Management Terminal Requirements Console Cable Conﬁguration Management Terminal ConnectionGeneral Setup Management Terminal Setup ParametersMenu Function Selection Display Setup SetupLocal Management Accessing Local Management Sehi Local ManagementFeature Selection Screen Local Management Using the Local Management Screens Community Name Table ScreenAccess Community NameEditing the Community Name Field Conﬁguration Screen IP AddressSetting the IP Address Default GatewayPort Enable Override SubNet MaskSetting the Subnet Mask Setting the Default Gateway Using the Port Enable OverrideExiting the Configuration Screen Trap Table ScreenTraps Configuring the Trap TableSnmp Community Name Trap IP AddressExiting the Trap Table Screen Snmp Tools ScreenSet OID PrependGet Get NextStep WalkRecall-OID CyclesGetting Individual OIDs Getting the Next OIDSetting an OID Viewing Multiple OIDsStepping Through OIDs Walking Through OIDsCycling Through OIDs Exiting the Snmp Tools Screen Device Statistics ScreenAlignment Errors Errors ReceivedCRC Errors Port Admin. StatusUpdate-Freq Enable PortDisable Port Port Seg. StatusUsing the Enable Port Command Selecting the Appropriate Module/PortUsing the Disable Port Command Exiting the Device Statistics ScreenAppendix a Twisted Pair Wiring Tables Twisted Pair Wiring TablesA-2 A-3 A-4 10BASE-T From Punch Down To RJ-45 Into Block Wallplate OfﬁceDrop Device A-6 A-7 SEHI-32/34 Punch Wall Plate Champ Down Block If Required Ethernet DeviceFigure A-1. Punch Down Block A-9 Spanish Power Supply CordGerman French