Cabletron Systems SEHI-34, SEHI-22, SEHI-32, SEHI-24 manual EPIM-2

Page 43

CONNECTING TO THE NETWORK

To connect twisted pair segments to the SEHI:

1.Insert the RJ45 connector from each twisted pair segment into the desired network port on the SEHI. See Figure 4-1.

18X

6X

17X

5X

16X

4X

15X

3X

14X

2X

13X

1X

EPIM-2

LNK

EPIM-T

LNK

EPIM-T

EPIM-1

Figure 4-1. SEHI-22/24 Network Ports

2.Check that the applicable LNK LED for the port is on. If the LED is not on, perform each of the following steps until it is:

a.Check that the 10BASE-T device at the other end of the twisted pair segment is powered up.

b.Verify that the RJ45 connector on the twisted pair segment has the proper pinouts. Check the cable for continuity.

c.Check that the twisted pair connection meets dB loss and cable specifications outlined Chapter 2.

If a link still has not been established, contact Cabletron Systems Technical Support.

Page 4-2

Image 43

Contents 10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper DOC Notice FCC NoticeCabletron Software Program License Cabletron SYSTEMS, INC Program License AgreementUnited States Government Restricted Rights Exclusion of Warranty Disclaimer of LiabilityTable of Contents Local Management InstallationConnecting to the Network TroubleshootingContents Appendix B Twisted Pair Wiring Tables A-1 Chapter Introduction Using this ManualSehi Overview Introduction Getting HelpFlash EEPROMs Sehi FeaturesRepeater Functionality Polarity Detection and CorrectionStackable Capabilities Reset ButtonLanview LEDs Local ManagementEpim Introduction Optional FeaturesRack Mount or Wall Mount Hardware Daughter Board Upgrade KitRelated Manuals HubSTACK Interconnect Cable Requirements Cable SpecificationsJitter LengthInsertion Loss ImpedanceNoise DelayTemperature CrosstalkCable Type Attenuation Maximum Cable Length Fiber Optic Budget and Propagation DelayInstallation REQUIREMENTS/SPECIFICATIONS Terminators ConnectorsThin-Net Network Requirements for the EPIM-C Module Cable TypeAUI Cable Requirements for the EPIM-A and EPIM-X Modules Network Port SpecificationsAUI Cable SEHI-32 and SEHI-34 Network Port Speciﬁcations SEHI-22 and SEHI-24 Network Port SpeciﬁcationsPin Champ Connector EPIM-T Installation REQUIREMENTS/SPECIFICATIONS Epim SpecificationsParameter Typical Worst Worst Case Typical Value Budget EPIM-F1 and EPIM-F2EPIM-F3 EPIM-F3Parameter Typical Minimum Maximum EPIM-C Connector TypeEPIM-A and EPIM-X EPIM-A and EPIM-X AUI PortTransceiver Requirements COMPreamble Delay Times Start of PacketsDelay Times JAM GeneralJAM Output Fault ProtectionPower Supply Requirements Output Min. Load Max. Load Max PowerPhysical SafetyUnpacking the Sehi Installing the SehiStacking the Sehi Stacking the Sehi Disconnect SEH and Sehi Interconnect Cables At the OUT Port Attaching the Strain Relief BracketRack Mounting the Sehi Installing the Sehi in the RackWall Mounting the Sehi Shelf or Table-top Installation Free-Standing InstallationInstallation Connecting the Sehi to the Power Source Connecting to Network Ports, SEHI-22 and SEHI-24 Connecting the Sehi to the NetworkEPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 EPIM-T Cross-over Switch Connecting a UTP Segment to an EPIM-TConnecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C EPIM-A Connecting an AUI Cable to an EPIM-AConnecting an AUI Cable to an EPIM-X On Position Toward Back Epim OFF Position Toward Front Finishing the InstallationInstallation CHECK-OUT Chapter TroubleshootingUsing Lanview CPU PWRLNK Troubleshooting CLNUsing the Reset Button RCVChapter Local Management Local Management Management Terminal Requirements Management Terminal Connection Console Cable ConﬁgurationSetup Management Terminal Setup ParametersMenu Function Selection Display Setup General SetupSehi Local Management Local Management Accessing Local ManagementFeature Selection Screen Community Name Table Screen Local Management Using the Local Management ScreensCommunity Name AccessEditing the Community Name Field IP Address Conﬁguration ScreenSubNet Mask Default GatewayPort Enable Override Setting the IP AddressSetting the Subnet Mask Using the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Configuration ScreenTrap IP Address Configuring the Trap TableSnmp Community Name TrapsSnmp Tools Screen Exiting the Trap Table ScreenGet Next OID PrependGet SetCycles WalkRecall-OID StepGetting the Next OID Getting Individual OIDsViewing Multiple OIDs Setting an OIDStepping Through OIDs Walking Through OIDsCycling Through OIDs Device Statistics Screen Exiting the Snmp Tools ScreenPort Admin. Status Errors ReceivedCRC Errors Alignment ErrorsPort Seg. Status Enable PortDisable Port Update-FreqSelecting the Appropriate Module/Port Using the Enable Port CommandExiting the Device Statistics Screen Using the Disable Port CommandTwisted Pair Wiring Tables Appendix a Twisted Pair Wiring TablesA-2 A-3 A-4 10BASE-T From Punch Down To RJ-45 Into Block Wallplate OfﬁceDrop Device A-6 A-7 Champ Down Block If Required Ethernet Device SEHI-32/34 Punch Wall PlateFigure A-1. Punch Down Block A-9 French Power Supply CordGerman Spanish