Cabletron Systems SEHI-24 Local Management Accessing Local Management, Sehi Local Management

Page 62

LOCAL MANAGEMENT

6.2ACCESSING LOCAL MANAGEMENT

After you conﬁgure the local management terminal and properly attach the cables to the SEHI, you can access the Local Management interface.

To access Local Management:

1.Power up the terminal. The SEHI Password screen shown in Figure 6-2 appears.

SEHI LOCAL MANAGEMENT

Cabletron SEHI Revision X.XX.XX

Cabletron Systems Incorporated

35 Industrial Way, P.O. Box 5005

Rochester, NH 03867-0505 U.S.A.

(603)332-9400

(c)Copyright Cabletron Systems, Inc. 1993

SEHI F/W Version: X.XX.XX

Boot Prom Version: X.XX.XX

SEHI Board Version: X.X

EnterUser Password:

Figure 6-2. Password Screen

2.Enter your Password. The factory default password for Super-User access is “public” or the Return key.

Note: Your password is one of the community names specified in the Community Name Table. Access to certain Local Management capabilities depends on the degree of access accorded that community name. See Section 6.3.1 for more details about community names.

Page 6-5

Image 62

Contents 10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper FCC Notice DOC NoticeCabletron SYSTEMS, INC Program License Agreement Cabletron Software Program LicenseExclusion of Warranty Disclaimer of Liability United States Government Restricted RightsTable of Contents Troubleshooting InstallationConnecting to the Network Local ManagementContents Appendix B Twisted Pair Wiring Tables A-1 Using this Manual Chapter IntroductionIntroduction Getting Help Sehi OverviewPolarity Detection and Correction Sehi FeaturesRepeater Functionality Flash EEPROMsLocal Management Reset ButtonLanview LEDs Stackable CapabilitiesIntroduction Optional Features EpimRelated Manuals Daughter Board Upgrade KitRack Mount or Wall Mount Hardware Cable Specifications HubSTACK Interconnect Cable RequirementsImpedance LengthInsertion Loss JitterCrosstalk DelayTemperature NoiseFiber Optic Budget and Propagation Delay Cable Type Attenuation Maximum Cable LengthInstallation REQUIREMENTS/SPECIFICATIONS Cable Type ConnectorsThin-Net Network Requirements for the EPIM-C Module TerminatorsAUI Cable Network Port SpecificationsAUI Cable Requirements for the EPIM-A and EPIM-X Modules SEHI-22 and SEHI-24 Network Port Speciﬁcations SEHI-32 and SEHI-34 Network Port SpeciﬁcationsPin Champ Connector Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications EPIM-TEPIM-F1 and EPIM-F2 Parameter Typical Worst Worst Case Typical Value BudgetEPIM-F3 EPIM-F3Parameter Typical Minimum Maximum Connector Type EPIM-CEPIM-A and EPIM-X AUI Port EPIM-A and EPIM-XCOM Transceiver RequirementsGeneral Delay Times Start of PacketsDelay Times JAM PreambleOutput Min. Load Max. Load Max Power Fault ProtectionPower Supply Requirements JAM OutputSafety PhysicalInstalling the Sehi Unpacking the SehiStacking the Sehi Stacking the Sehi Attaching the Strain Relief Bracket Disconnect SEH and Sehi Interconnect Cables At the OUT PortInstalling the Sehi in the Rack Rack Mounting the SehiWall Mounting the Sehi Free-Standing Installation Shelf or Table-top InstallationInstallation Connecting the Sehi to the Power Source Connecting the Sehi to the Network Connecting to Network Ports, SEHI-22 and SEHI-24EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 Connecting a UTP Segment to an EPIM-T EPIM-T Cross-over SwitchConnecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C Connecting an AUI Cable to an EPIM-A EPIM-AConnecting an AUI Cable to an EPIM-X Finishing the Installation On Position Toward Back Epim OFF Position Toward FrontChapter Troubleshooting Installation CHECK-OUTUsing Lanview PWR CPURCV Troubleshooting CLNUsing the Reset Button LNKChapter Local Management Local Management Management Terminal Requirements Console Cable Conﬁguration Management Terminal ConnectionGeneral Setup Management Terminal Setup ParametersMenu Function Selection Display Setup SetupLocal Management Accessing Local Management Sehi Local ManagementFeature Selection Screen Local Management Using the Local Management Screens Community Name Table ScreenAccess Community NameEditing the Community Name Field Conﬁguration Screen IP AddressSetting the IP Address Default GatewayPort Enable Override SubNet MaskSetting the Subnet Mask Setting the Default Gateway Using the Port Enable OverrideExiting the Configuration Screen Trap Table ScreenTraps Configuring the Trap TableSnmp Community Name Trap IP AddressExiting the Trap Table Screen Snmp Tools ScreenSet OID PrependGet Get NextStep WalkRecall-OID CyclesGetting Individual OIDs Getting the Next OIDSetting an OID Viewing Multiple OIDsCycling Through OIDs Walking Through OIDsStepping Through OIDs Exiting the Snmp Tools Screen Device Statistics ScreenAlignment Errors Errors ReceivedCRC Errors Port Admin. StatusUpdate-Freq Enable PortDisable Port Port Seg. StatusUsing the Enable Port Command Selecting the Appropriate Module/PortUsing the Disable Port Command Exiting the Device Statistics ScreenAppendix a Twisted Pair Wiring Tables Twisted Pair Wiring TablesA-2 A-3 A-4 Drop Device From Punch Down To RJ-45 Into Block Wallplate Ofﬁce10BASE-T A-6 A-7 SEHI-32/34 Punch Wall Plate Champ Down Block If Required Ethernet DeviceFigure A-1. Punch Down Block A-9 Spanish Power Supply CordGerman French