Cabletron Systems SEHI-34, SEHI-22, SEHI-32 Exiting the Configuration Screen, Trap Table Screen

Page 71

LOCAL MANAGEMENT

Exiting the Configuration Screen

1.To exit the Configuration screen, press the appropriate Function key. To return to the Feature Selection screen, use the arrow keys to highlight the RETURN command.

2.Press the Return key. The Feature Selection screen appears.

6.3.3The Trap Table Screen

To access the Trap Table screen from the Features Selection screen, use the arrow keys to highlight the Component Trap Table option, then press the Return key or F8. The Trap Table screen shown in Figure 6-6 appears.

SEHI LOCAL MANAGEMENT

Cabletron SEHI Revision X.XX.XX

TRAP TABLE

SNMP Community Name			Traps	IP Address

<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
<CR>			N	0.0.0.0
			N	0.0.0.0
SAVE	COMMUNITY NAMES	IP TABLE	SNMP TOOLS	RETURN
F6	F7	F8	F9

Figure 6-6. Trap Table Screen

The Trap Table deﬁnes the management stations that will receive SNMP Traps for alarm/event notiﬁcation. The following sections explain each ﬁeld on the Trap Table screen and instructions on how to change them.

Page 6-14

Image 71

Contents 10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper DOC Notice FCC NoticeCabletron Software Program License Cabletron SYSTEMS, INC Program License AgreementUnited States Government Restricted Rights Exclusion of Warranty Disclaimer of LiabilityTable of Contents Local Management InstallationConnecting to the Network TroubleshootingContents Appendix B Twisted Pair Wiring Tables A-1 Chapter Introduction Using this ManualSehi Overview Introduction Getting HelpFlash EEPROMs Sehi FeaturesRepeater Functionality Polarity Detection and CorrectionStackable Capabilities Reset ButtonLanview LEDs Local ManagementEpim Introduction Optional FeaturesRelated Manuals Daughter Board Upgrade KitRack Mount or Wall Mount Hardware HubSTACK Interconnect Cable Requirements Cable SpecificationsJitter LengthInsertion Loss ImpedanceNoise DelayTemperature CrosstalkCable Type Attenuation Maximum Cable Length Fiber Optic Budget and Propagation DelayInstallation REQUIREMENTS/SPECIFICATIONS Terminators ConnectorsThin-Net Network Requirements for the EPIM-C Module Cable TypeAUI Cable Network Port SpecificationsAUI Cable Requirements for the EPIM-A and EPIM-X Modules SEHI-32 and SEHI-34 Network Port Speciﬁcations SEHI-22 and SEHI-24 Network Port SpeciﬁcationsPin Champ Connector EPIM-T Installation REQUIREMENTS/SPECIFICATIONS Epim SpecificationsParameter Typical Worst Worst Case Typical Value Budget EPIM-F1 and EPIM-F2EPIM-F3 EPIM-F3Parameter Typical Minimum Maximum EPIM-C Connector TypeEPIM-A and EPIM-X EPIM-A and EPIM-X AUI PortTransceiver Requirements COMPreamble Delay Times Start of PacketsDelay Times JAM GeneralJAM Output Fault ProtectionPower Supply Requirements Output Min. Load Max. Load Max PowerPhysical SafetyUnpacking the Sehi Installing the SehiStacking the Sehi Stacking the Sehi Disconnect SEH and Sehi Interconnect Cables At the OUT Port Attaching the Strain Relief BracketRack Mounting the Sehi Installing the Sehi in the RackWall Mounting the Sehi Shelf or Table-top Installation Free-Standing InstallationInstallation Connecting the Sehi to the Power Source Connecting to Network Ports, SEHI-22 and SEHI-24 Connecting the Sehi to the NetworkEPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 EPIM-T Cross-over Switch Connecting a UTP Segment to an EPIM-TConnecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C EPIM-A Connecting an AUI Cable to an EPIM-AConnecting an AUI Cable to an EPIM-X On Position Toward Back Epim OFF Position Toward Front Finishing the InstallationInstallation CHECK-OUT Chapter TroubleshootingUsing Lanview CPU PWRLNK Troubleshooting CLNUsing the Reset Button RCVChapter Local Management Local Management Management Terminal Requirements Management Terminal Connection Console Cable ConﬁgurationSetup Management Terminal Setup ParametersMenu Function Selection Display Setup General SetupSehi Local Management Local Management Accessing Local ManagementFeature Selection Screen Community Name Table Screen Local Management Using the Local Management ScreensCommunity Name AccessEditing the Community Name Field IP Address Conﬁguration ScreenSubNet Mask Default GatewayPort Enable Override Setting the IP AddressSetting the Subnet Mask Using the Port Enable Override Setting the Default GatewayTrap Table Screen Exiting the Configuration ScreenTrap IP Address Configuring the Trap TableSnmp Community Name TrapsSnmp Tools Screen Exiting the Trap Table ScreenGet Next OID PrependGet SetCycles WalkRecall-OID StepGetting the Next OID Getting Individual OIDsViewing Multiple OIDs Setting an OIDCycling Through OIDs Walking Through OIDsStepping Through OIDs Device Statistics Screen Exiting the Snmp Tools ScreenPort Admin. Status Errors ReceivedCRC Errors Alignment ErrorsPort Seg. Status Enable PortDisable Port Update-FreqSelecting the Appropriate Module/Port Using the Enable Port CommandExiting the Device Statistics Screen Using the Disable Port CommandTwisted Pair Wiring Tables Appendix a Twisted Pair Wiring TablesA-2 A-3 A-4 Drop Device From Punch Down To RJ-45 Into Block Wallplate Ofﬁce10BASE-T A-6 A-7 Champ Down Block If Required Ethernet Device SEHI-32/34 Punch Wall PlateFigure A-1. Punch Down Block A-9 French Power Supply CordGerman Spanish