Cabletron Systems SEHI-22, SEHI-32 Free-Standing Installation, Shelf or Table-top Installation

Page 40

INSTALLATION

3.You will need a pencil for this step. With the wall mounting brackets attached to the SEHI, position the SEHI against the wall where it will be permanently mounted with the network port facing down. Use the pencil to mark the wall location for the four pilot holes.

4.Set the SEHI aside and carefully drill four 1/4" pilot holes, one for each of the Molly screw anchors and insert the four Molly screw anchors into the holes just drilled.

5.Tighten each of the anchor screws until the anchor expands holding the anchor firmly in the wall, then remove the screws completely.

6.Position the SEHI on the wall over the anchors and reinstall the four anchor screws to attach the SEHI to the wall, as shown in Figure 3-6. Tighten the four anchor screws.

3.2.5Free-Standing Installation

For a free-standing shelf or tabletop installation, locate the SEHI within 7 feet of its power source and with an unrestricted free surface area 21 inches wide, 18 inches deep and 6 inches high, as shown in Figure 3-7.

18 IN.

HubSTACK 10BASE-T HUB WITH LANVIEW®

SEHI-24

6 IN.

21 IN.

7 FT.

Figure 3-7. Shelf or Table-top Installation

Page 3-7

Image 40

Contents 10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper FCC Notice DOC NoticeCabletron SYSTEMS, INC Program License Agreement Cabletron Software Program LicenseExclusion of Warranty Disclaimer of Liability United States Government Restricted RightsTable of Contents Installation Connecting to the NetworkTroubleshooting Local ManagementContents Appendix B Twisted Pair Wiring Tables A-1 Using this Manual Chapter IntroductionIntroduction Getting Help Sehi OverviewSehi Features Repeater FunctionalityPolarity Detection and Correction Flash EEPROMsReset Button Lanview LEDsLocal Management Stackable CapabilitiesIntroduction Optional Features EpimRack Mount or Wall Mount Hardware Daughter Board Upgrade KitRelated Manuals Cable Specifications HubSTACK Interconnect Cable RequirementsLength Insertion LossImpedance JitterDelay TemperatureCrosstalk NoiseFiber Optic Budget and Propagation Delay Cable Type Attenuation Maximum Cable LengthInstallation REQUIREMENTS/SPECIFICATIONS Connectors Thin-Net Network Requirements for the EPIM-C ModuleCable Type TerminatorsAUI Cable Requirements for the EPIM-A and EPIM-X Modules Network Port SpecificationsAUI Cable SEHI-22 and SEHI-24 Network Port Speciﬁcations SEHI-32 and SEHI-34 Network Port SpeciﬁcationsPin Champ Connector Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications EPIM-TEPIM-F1 and EPIM-F2 Parameter Typical Worst Worst Case Typical Value BudgetEPIM-F3 EPIM-F3Parameter Typical Minimum Maximum Connector Type EPIM-CEPIM-A and EPIM-X AUI Port EPIM-A and EPIM-XCOM Transceiver RequirementsDelay Times Start of Packets Delay Times JAMGeneral PreambleFault Protection Power Supply RequirementsOutput Min. Load Max. Load Max Power JAM OutputSafety PhysicalInstalling the Sehi Unpacking the SehiStacking the Sehi Stacking the Sehi Attaching the Strain Relief Bracket Disconnect SEH and Sehi Interconnect Cables At the OUT PortInstalling the Sehi in the Rack Rack Mounting the SehiWall Mounting the Sehi Free-Standing Installation Shelf or Table-top InstallationInstallation Connecting the Sehi to the Power Source Connecting the Sehi to the Network Connecting to Network Ports, SEHI-22 and SEHI-24EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 Connecting a UTP Segment to an EPIM-T EPIM-T Cross-over SwitchConnecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C Connecting an AUI Cable to an EPIM-A EPIM-AConnecting an AUI Cable to an EPIM-X Finishing the Installation On Position Toward Back Epim OFF Position Toward FrontChapter Troubleshooting Installation CHECK-OUTUsing Lanview PWR CPUTroubleshooting CLN Using the Reset ButtonRCV LNKChapter Local Management Local Management Management Terminal Requirements Console Cable Conﬁguration Management Terminal ConnectionManagement Terminal Setup Parameters Menu Function Selection Display SetupGeneral Setup SetupLocal Management Accessing Local Management Sehi Local ManagementFeature Selection Screen Local Management Using the Local Management Screens Community Name Table ScreenAccess Community NameEditing the Community Name Field Conﬁguration Screen IP AddressDefault Gateway Port Enable OverrideSetting the IP Address SubNet MaskSetting the Subnet Mask Setting the Default Gateway Using the Port Enable OverrideExiting the Configuration Screen Trap Table ScreenConfiguring the Trap Table Snmp Community NameTraps Trap IP AddressExiting the Trap Table Screen Snmp Tools ScreenOID Prepend GetSet Get NextWalk Recall-OIDStep CyclesGetting Individual OIDs Getting the Next OIDSetting an OID Viewing Multiple OIDsStepping Through OIDs Walking Through OIDsCycling Through OIDs Exiting the Snmp Tools Screen Device Statistics ScreenErrors Received CRC ErrorsAlignment Errors Port Admin. StatusEnable Port Disable PortUpdate-Freq Port Seg. StatusUsing the Enable Port Command Selecting the Appropriate Module/PortUsing the Disable Port Command Exiting the Device Statistics ScreenAppendix a Twisted Pair Wiring Tables Twisted Pair Wiring TablesA-2 A-3 A-4 10BASE-T From Punch Down To RJ-45 Into Block Wallplate OfﬁceDrop Device A-6 A-7 SEHI-32/34 Punch Wall Plate Champ Down Block If Required Ethernet DeviceFigure A-1. Punch Down Block A-9 Power Supply Cord GermanSpanish French