EMC QLA23xx, QLA22xx Introduction, Downloading QLogic Drivers Firmware Verifying Documentation

Page 14

2

Installing and Configuring the HBA Driver

Introduction

Downloading

QLogic Drivers and

Firmware

Verifying and

Downloading the

Documentation

The procedure described here was written specifically for the QLA22xx and QLA23xx families of Fibre Channel HBAs; however, the procedures for installing the adapter BIOS and Windows drivers are identical for QLA21xx, QLA22xx, and QLA23xx.

When installing or upgrading the BIOS and drivers, be sure to use the latest versions supported by EMC. Review the EMC Support Matrix for the latest information on approved HBAs and drivers.

Also refer to the EMC Host Connectivity Guide for Windows 2000 and Windows NT, available on Powerlink, for related information.

If you need to download the latest HBA driver or firmware:

1.Access www.qlogic.com.

2.Click Downloads at the left side of the screen.

3.Click the EMC link to the right of OEM-approved Drivers/Firmware.

4.Find the description of your HBA driver in the Name column of the table for your HBA model. Then click the Download link in the associated Download column.

To check for the latest revision of this document (and download it if necessary):

1.Access www.qlogic.com.

2.Click Downloads at the left side of the screen.

3.Click the EMC link to the right of OEM-approved Drivers/Firmware.

4.Find the description of your HBA driver in the Name column of the table for your HBA model. Then click the Readme link in the associated Description column.

2-2

EMC Fibre Channel with QLogic HBAs in Windows Hosts

 

 

Image 14
Contents REV A01 August Copyright 2001-2003 EMC Corporation. All rights reserved Trademark InformationContents Chapter Configuring an EMC Boot Device LUNAppendix a Third-Party Software Appendix B TroubleshootingProblems and Solutions Index EMC Fibre Channel with QLogic HBAs in Windows Hosts Damage to the system or equipment. The caution may apply to PrefaceEMC uses the following conventions for notes, cautions, Hardware or softwareBold Related Documentation Typographical ConventionsPalatino Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Introduction Downloading QLogic Drivers Firmware Verifying DocumentationInstalling an HBA Check for an Updated HBA Driver Reconfigure the HBA Jumper Move the jumpers, onto pins 1-2 if not already thereSet the HBA FC-AL Loop ID Installing an HBA Settings EMC HBA SettingsPre-Configured Advanced Adapter Settings , and Extended Firmware SettingsConfiguring Nvram for Stratus ftServers To set the first HBA, follow these proceduresWith Embedded Firmware/BIOSFibre-Down Servers QLogic HBAsTo load firmware/BIOS and Nvram settings, type Example Flasutil /L /F /N NVRAM23o.DATPress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Administrative Tools, Computer Management Select have DiskEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device How to Determine I/O Latency and Load on the Boot LUNBehavior Boot CrashdumpSave to Disk Configuring a Symmetrix Boot Device Select Current Boot Node Name and press Enter From the Configuration Settings menu, select Host AdapterFrom the Host Adapter Settings menu, select Host Adapter Configuration Settings menuWindows OS onto InstallingBoot Device Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Flowchart Configuring a CLARiiON Boot DeviceProcedure Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Requirements, and related documentation Configurations, Revisions Hardware Software RequirementsRequirements TopologiesRequired media includes the following Preparing the Storage SystemMedia Requirements Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts Continue to Preparing the Server on Node NameWhat Next? Preparing the Server Physical Connection of Only One SP Port to the FabricConfiguring the HP ProLiant BL20p G2 Select Set Boot Controller OrderConfiguring the HBA Boot BiosCTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Additional Boot Port Installing AdditionalConfiguring Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device Trespassing the Boot LUN Using atftrespass On the Computer Management window, click Disk ManagementStarting a Fresh Installation Boot Time and LUN Availability Replacing a Boot HBA EMC Symmetrix EMC CLARiiONExplanations of Entries How a Server Responds to Failure in the Boot LUN PathStop Error fatal blue screen Indicates host failure Known Issues Ntosknl BsodEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager Veritas Volume Manager 3.x for Windows After completing these changes, reboot the host systemEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Solution Problems and SolutionsProblem EMC Primus case emc69308 Direct-connect to EMC CLARiiON EMC Support. Windows 2003 driver 8.2.2.20 and later alreadyContain this correction A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index