EMC QLA23xx, QLA22xx manual Check for an Updated HBA Driver

Page 16

2

Installing and Configuring the HBA Driver

4.Label each cable to identify the HBA and the storage/switch/hub port to which it connects.

5.After connecting all HBAs in the server, power up the server.

Special Installation Sequence for Stratus ftServers and EMC CLARiiON Arrays

A specific installation sequence is required when installing QLogic HBAs with the Stratus ftServers and EMC CLARiiON® storage. Failure to follow this sequence may result in a STOP: 0X0000007B bugcheck error when booting the Stratus server for the first time when connected to EMC CLARiiON storage.

With the Stratus ftServer, if the HBA detects EMC CLARiiON array targets but no accessible LUNS, it prevents the Stratus server from booting. In this configuration, the Stratus ftServer attempts to boot from the array, instead of booting from the internal boot drive.

To avoid this issue before storage is correctly assigned, either boot the Stratus ftServer before connecting the fibre cables to the HBAs or, if connected to a fabric, disable the HBA ports on the switch before booting the ftServer.

After the system has booted, connect the cables or reenable the switch ports. Verify that the HBAs are logged in to the EMC CLARiiON array; then stop and restart the Navisphere agent on the ftServer host. This will register the HBAs with the CLARiiON array and allow the HBA to properly detect the available LUNS.

Special Instructions for CLARiiON CX200-Series Direct-Connect Dual-Host Clustering Configurations

Check for an Updated HBA Driver

For CLARiiON CX200-Series direct-connect dual-host cluster configurations only with QLA234x HBAs, you must follow all procedures described in this section.

For CLARiiON CX200-Series direct-connect dual-host cluster configurations with only QLA234x HBAs, you may need a separate driver and firmware download. The EMC Support Matrix notes whether separate driver and firmware files are required.

For each HBA that is determined to require updated firmware and drivers, follow the instructions under Downloading QLogic Drivers and Firmware on page 2-2. Be sure to reference the Name and Description

2-4

EMC Fibre Channel with QLogic HBAs in Windows Hosts

 

 

Image 16
Contents REV A01 August Copyright 2001-2003 EMC Corporation. All rights reserved Trademark InformationContents Chapter Configuring an EMC Boot Device LUNProblems and Solutions Index Appendix B TroubleshootingAppendix a Third-Party Software EMC Fibre Channel with QLogic HBAs in Windows Hosts Preface EMC uses the following conventions for notes, cautions,Damage to the system or equipment. The caution may apply to Hardware or softwarePalatino Related Documentation Typographical ConventionsBold Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Introduction Downloading QLogic Drivers Firmware Verifying DocumentationInstalling an HBA Check for an Updated HBA Driver Reconfigure the HBA Jumper Move the jumpers, onto pins 1-2 if not already thereSet the HBA FC-AL Loop ID Installing an HBA EMC HBA Settings Pre-ConfiguredSettings Advanced Adapter Settings , and Extended Firmware SettingsConfiguring Nvram for Stratus ftServers To set the first HBA, follow these proceduresFirmware/BIOS Fibre-Down ServersWith Embedded QLogic HBAsTo load firmware/BIOS and Nvram settings, type Example Flasutil /L /F /N NVRAM23o.DATPress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Administrative Tools, Computer Management Select have DiskEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device How to Determine I/O Latency and Load on the Boot LUNSave to Disk Boot CrashdumpBehavior Configuring a Symmetrix Boot Device From the Configuration Settings menu, select Host Adapter From the Host Adapter Settings menu, select Host AdapterSelect Current Boot Node Name and press Enter Configuration Settings menuInstalling Boot DeviceWindows OS onto Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Configuring a CLARiiON Boot Device ProcedureFlowchart Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Configurations, Revisions Hardware Software Requirements RequirementsRequirements, and related documentation TopologiesMedia Requirements Preparing the Storage SystemRequired media includes the following Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts What Next? Node NameContinue to Preparing the Server on Preparing the Server Physical Connection of Only One SP Port to the FabricConfiguring the HP ProLiant BL20p G2 Select Set Boot Controller OrderConfiguring the HBA Boot BiosCTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Installing Additional ConfiguringAdditional Boot Port Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device Trespassing the Boot LUN Using atftrespass On the Computer Management window, click Disk ManagementStarting a Fresh Installation Boot Time and LUN Availability Replacing a Boot HBA EMC Symmetrix EMC CLARiiONStop Error fatal blue screen Indicates host failure How a Server Responds to Failure in the Boot LUN PathExplanations of Entries Known Issues Ntosknl BsodEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager Veritas Volume Manager 3.x for Windows After completing these changes, reboot the host systemEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Problem Problems and SolutionsSolution EMC Support. Windows 2003 driver 8.2.2.20 and later already Contain this correctionEMC Primus case emc69308 Direct-connect to EMC CLARiiON A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index