EMC QLA22xx, QLA23xx manual HP ProLiant BL20p G2 Windows Installation

Page 41

HP ProLiant BL20p G2

Windows 2000

Installation

Configuring an EMC Boot Device

1.Note these prerequisites:

•RDP server with release 1.30

•BfS Installation script, see HP ProLiant BL20p G2 documentation for creation and installation of this script.

2.Configure BL20p G2. Then reboot the BL20p G2 and select F9 to RBSU (F10 to save all changes before exit).

a. Select Set Boot Controller Order

i.Ctrl:1 PCI Dual Port Fibre..Port 1

ii.Ctrl:2 PCI Dual Port Fibre..Port 2

iii.Ctrl:3 HP Smart Array 5i Ctrl

b.Set IPL order as follows:

i.PCI Embedded HP NC7781 Gig Server Adapter Port 1

ii.CD-ROM

iii.Floppy Drive

iv.Hard Drive C:

3.Install the Windows 2000 OS:

a.If there is a local hard drive installed, remove it. This drive can be reinserted after the installation is completed.

b.Open an interface window using the RDP console by Right-clicking the target server and selecting Power Control/ RILOE Interface.

c.Delete the target server (BfS Server) from the RDP database if it exists.

d.Reboot the BfS server. (At boot time, the newly created LUN should be detected.)

The BfS server should now be seen in the RDP New Computer pane.

e.Start the BfS deployment by dragging and dropping the BOOT FROM SAN BL20p script task to the BfS server new computer

Installation time is approximately 50 minutes.

3

Configuring a Symmetrix Boot Device	3-9

Image 41

Contents REV A01 August Trademark Information Copyright 2001-2003 EMC Corporation. All rights reservedContents LUN Chapter Configuring an EMC Boot DeviceAppendix a Third-Party Software Appendix B TroubleshootingProblems and Solutions Index EMC Fibre Channel with QLogic HBAs in Windows Hosts EMC uses the following conventions for notes, cautions, PrefaceDamage to the system or equipment. The caution may apply to Hardware or softwareBold Related Documentation Typographical ConventionsPalatino Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Downloading QLogic Drivers Firmware Verifying Documentation IntroductionInstalling an HBA Check for an Updated HBA Driver Move the jumpers, onto pins 1-2 if not already there Reconfigure the HBA JumperSet the HBA FC-AL Loop ID Installing an HBA Pre-Configured EMC HBA SettingsSettings Advanced Adapter Settings , and Extended Firmware SettingsTo set the first HBA, follow these procedures Configuring Nvram for Stratus ftServersFibre-Down Servers Firmware/BIOSWith Embedded QLogic HBAsExample Flasutil /L /F /N NVRAM23o.DAT To load firmware/BIOS and Nvram settings, typePress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Select have Disk Administrative Tools, Computer ManagementEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device LUN How to Determine I/O Latency and Load on the BootBehavior Boot CrashdumpSave to Disk Configuring a Symmetrix Boot Device From the Host Adapter Settings menu, select Host Adapter From the Configuration Settings menu, select Host AdapterSelect Current Boot Node Name and press Enter Configuration Settings menuBoot Device InstallingWindows OS onto Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Procedure Configuring a CLARiiON Boot DeviceFlowchart Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Requirements Configurations, Revisions Hardware Software RequirementsRequirements, and related documentation TopologiesRequired media includes the following Preparing the Storage SystemMedia Requirements Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts Continue to Preparing the Server on Node NameWhat Next? Physical Connection of Only One SP Port to the Fabric Preparing the ServerSelect Set Boot Controller Order Configuring the HP ProLiant BL20p G2Boot Bios Configuring the HBACTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring Installing AdditionalAdditional Boot Port Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device On the Computer Management window, click Disk Management Trespassing the Boot LUN Using atftrespassStarting a Fresh Installation Boot Time and LUN Availability EMC Symmetrix EMC CLARiiON Replacing a Boot HBAExplanations of Entries How a Server Responds to Failure in the Boot LUN PathStop Error fatal blue screen Indicates host failure Ntosknl Bsod Known IssuesEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager After completing these changes, reboot the host system Veritas Volume Manager 3.x for WindowsEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Solution Problems and SolutionsProblem Contain this correction EMC Support. Windows 2003 driver 8.2.2.20 and later alreadyEMC Primus case emc69308 Direct-connect to EMC CLARiiON A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index