EMC QLA23xx, QLA22xx manual HP ProLiant BL20p G2 Windows 2000 OS Installation

Page 56

3

Configuring an EMC Boot Device

HP ProLiant BL20p G2

Windows 2000 OS

Installation

Select NTFS file system format, which is suitable for most sites unless you have other specific requirements. Then press ENTER. (For background information on the choice of the NTFS file system, refer to Microsoft Knowledge Base Article 0184006.)

Setup now formats the partition, copies the Windows system files to the partition, and starts rebooting the server.

11.When prompted, remove the diskette and CD-ROM.

If your system prompts you to press any key to boot from CD-ROM, do not press a key; allow the system to boot from the HBA adapter.

After booting, the system continues installation, displays the Windows banner, and begins autodetection of mass-storage devices and adapters.

12.Follow the on-screen instructions to complete the installation.

When the Completing the Windows Setup Wizard screen appears, click Finish.

13.If you plan to add SCSI disks in the future, you should disable the BIOS for the managing SCSI controller so that the system does not attempt to boot from those disks. For information, refer to Preparing the Server on page 3-18.

14.Install the latest EMC-approved Windows Service Pack as explained in the Microsoft documentation.

For HP ProLiant BL20p G2 servers:

1.If there is a local hard drive installed, remove it. This drive can be reinserted after the installation is completed.

2.Open an interface window using the RDP console by right-clicking the target server and selecting Power Control/ RILOE Interface.

3.Delete the target server (BfS Server) from the RDP database if it exists.

4.Reboot the BfS server. (At boot time, the newly created LUN should be detected.)

The BfS server should now be seen in the RDP New Computer pane.

3-24	EMC Fibre Channel with QLogic HBAs in Windows Hosts

Image 56

Contents REV A01 August Copyright 2001-2003 EMC Corporation. All rights reserved Trademark InformationContents Chapter Configuring an EMC Boot Device LUNAppendix a Third-Party Software Appendix B TroubleshootingProblems and Solutions Index EMC Fibre Channel with QLogic HBAs in Windows Hosts Preface EMC uses the following conventions for notes, cautions,Damage to the system or equipment. The caution may apply to Hardware or softwareBold Related Documentation Typographical ConventionsPalatino Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Introduction Downloading QLogic Drivers Firmware Verifying DocumentationInstalling an HBA Check for an Updated HBA Driver Reconfigure the HBA Jumper Move the jumpers, onto pins 1-2 if not already thereSet the HBA FC-AL Loop ID Installing an HBA EMC HBA Settings Pre-ConfiguredSettings Advanced Adapter Settings , and Extended Firmware SettingsConfiguring Nvram for Stratus ftServers To set the first HBA, follow these proceduresFirmware/BIOS Fibre-Down ServersWith Embedded QLogic HBAsTo load firmware/BIOS and Nvram settings, type Example Flasutil /L /F /N NVRAM23o.DATPress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Administrative Tools, Computer Management Select have DiskEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device How to Determine I/O Latency and Load on the Boot LUNBehavior Boot CrashdumpSave to Disk Configuring a Symmetrix Boot Device From the Configuration Settings menu, select Host Adapter From the Host Adapter Settings menu, select Host AdapterSelect Current Boot Node Name and press Enter Configuration Settings menuInstalling Boot DeviceWindows OS onto Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Configuring a CLARiiON Boot Device ProcedureFlowchart Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Configurations, Revisions Hardware Software Requirements RequirementsRequirements, and related documentation TopologiesRequired media includes the following Preparing the Storage SystemMedia Requirements Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts Continue to Preparing the Server on Node NameWhat Next? Preparing the Server Physical Connection of Only One SP Port to the FabricConfiguring the HP ProLiant BL20p G2 Select Set Boot Controller OrderConfiguring the HBA Boot BiosCTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Installing Additional ConfiguringAdditional Boot Port Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device Trespassing the Boot LUN Using atftrespass On the Computer Management window, click Disk ManagementStarting a Fresh Installation Boot Time and LUN Availability Replacing a Boot HBA EMC Symmetrix EMC CLARiiONExplanations of Entries How a Server Responds to Failure in the Boot LUN PathStop Error fatal blue screen Indicates host failure Known Issues Ntosknl BsodEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager Veritas Volume Manager 3.x for Windows After completing these changes, reboot the host systemEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Solution Problems and SolutionsProblem EMC Support. Windows 2003 driver 8.2.2.20 and later already Contain this correctionEMC Primus case emc69308 Direct-connect to EMC CLARiiON A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index