EMC QLA22xx, QLA23xx manual Configuring a CLARiiON Boot Device

Page 61

Configuring an EMC Boot Device

To trespass the LUN, follow the instructions in the EMC ControlCenter Navisphere Management software documentation for your array type. The process depends on the failover software installed:

With PowerPath configurations, this can usually be done from the EMC ControlCenter Navisphere Management software GUI by right-clicking the desired LUN and selecting trespass. Confirm in the LUN properties that the LUN has trespassed before you return to configure the remaining Boot Port Name entries.

With ATF configurations:

With FC-series array core code 8.45.x, this can usually be done from the EMC ControlCenter Navisphere Management software GUI by right-clicking on the desired LUN and selecting trespass. Confirm in the LUN properties that the LUN has trespassed before you return to configure the remaining Boot Port Name entries.

With FC-series array core code 8.44.x and earlier, you will use the atf_trespass command to trespass the boot LUN. To do this, follow the steps under Trespassing the Boot LUN Using atf_trespass on page 3-30.

Each HBA can support multiple entries; you should configure Boot Port Name entries connecting to multiple ports on both SPs for maximum redundancy in booting after a boot LUN trespass or other link failures. Refer to Table 3-1 on page 3-34 to determine your high-availability requirements.

7.When all parameters are set correctly and you have added Boot Port Name entries for all the SP ports from which you would like to attempt to boot, press ESC to return to the Fast!UTIL Options menu; then select Save Changes to save the changes you made to the current adapter.

8.Press ESC to exit the Fast!UTIL Options menu.

9.Reboot the server.

Configuring a CLARiiON Boot Device

3-29

 

 

3

Image 61
Contents REV A01 August Trademark Information Copyright 2001-2003 EMC Corporation. All rights reservedContents LUN Chapter Configuring an EMC Boot DeviceProblems and Solutions Index Appendix B TroubleshootingAppendix a Third-Party Software EMC Fibre Channel with QLogic HBAs in Windows Hosts EMC uses the following conventions for notes, cautions, PrefaceDamage to the system or equipment. The caution may apply to Hardware or softwarePalatino Related Documentation Typographical ConventionsBold Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Downloading QLogic Drivers Firmware Verifying Documentation IntroductionInstalling an HBA Check for an Updated HBA Driver Move the jumpers, onto pins 1-2 if not already there Reconfigure the HBA JumperSet the HBA FC-AL Loop ID Installing an HBA Pre-Configured EMC HBA SettingsSettings Advanced Adapter Settings , and Extended Firmware SettingsTo set the first HBA, follow these procedures Configuring Nvram for Stratus ftServersFibre-Down Servers Firmware/BIOSWith Embedded QLogic HBAsExample Flasutil /L /F /N NVRAM23o.DAT To load firmware/BIOS and Nvram settings, typePress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Select have Disk Administrative Tools, Computer ManagementEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device LUN How to Determine I/O Latency and Load on the BootSave to Disk Boot CrashdumpBehavior Configuring a Symmetrix Boot Device From the Host Adapter Settings menu, select Host Adapter From the Configuration Settings menu, select Host AdapterSelect Current Boot Node Name and press Enter Configuration Settings menuBoot Device InstallingWindows OS onto Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Procedure Configuring a CLARiiON Boot DeviceFlowchart Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Requirements Configurations, Revisions Hardware Software RequirementsRequirements, and related documentation TopologiesMedia Requirements Preparing the Storage SystemRequired media includes the following Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts What Next? Node NameContinue to Preparing the Server on Physical Connection of Only One SP Port to the Fabric Preparing the ServerSelect Set Boot Controller Order Configuring the HP ProLiant BL20p G2Boot Bios Configuring the HBACTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring Installing AdditionalAdditional Boot Port Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device On the Computer Management window, click Disk Management Trespassing the Boot LUN Using atftrespassStarting a Fresh Installation Boot Time and LUN Availability EMC Symmetrix EMC CLARiiON Replacing a Boot HBAStop Error fatal blue screen Indicates host failure How a Server Responds to Failure in the Boot LUN PathExplanations of Entries Ntosknl Bsod Known IssuesEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager After completing these changes, reboot the host system Veritas Volume Manager 3.x for WindowsEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Problem Problems and SolutionsSolution Contain this correction EMC Support. Windows 2003 driver 8.2.2.20 and later alreadyEMC Primus case emc69308 Direct-connect to EMC CLARiiON A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index