EMC QLA22xx, QLA23xx manual Ctrl-Q

Page 53

Configuring an EMC Boot Device

register the HBA connection. If you will later install PowerPath or ATF, be sure to select the corresponding parameters during the registration procedure. Refer to your EMC ControlCenter Navisphere Management software, ATF, or PowerPath documentation for detailed instructions.

6.Press ESC until you exit the Fast!UTIL Options menu. You do not need to save any changes if prompted.

7.Reboot the server.

When the QLogic BIOS banner (shown in step 1) appears, press

CTRL–Q.

Different HBA models may display different banners. Be sure to select CTRL-Qfor the HBA you wish to configure.

8.After Fast!UTIL loads, the display depends on whether there are multiple QLogic HBAs installed:

If there is only one QLogic HBA, the Fast!UTIL Options menu appears.

If there are multiple QLogic HBAs, a list of addresses occupies by those HBAs appears. Use the arrow keys to select the desired HBA; then press ENTER. The Fast!UTIL Options menu appears.

9.Select Configuration Settings from the menu.

10.Select Selectable Boot Settings from the Configuration Settings menu.

Select the first Boot Port Name entry, and in the Device window select the CLARiiON port WWN from which you want to boot.

After you select the WWN, if there is more than one LUN detected, select the boot LUN number from the next window.

11.When all parameters are set correctly, press ESC to return to the Fast!UTIL Options menu; then select Save Changes to save the changes you made to the current adapter.

12.Press ESC to exit the Fast!UTIL Options menu.

13.Reboot the server.

What Next? Install Windows as described in the next section.

Configuring a CLARiiON Boot Device

3-21

 

 

3

Image 53
Contents REV A01 August Trademark Information Copyright 2001-2003 EMC Corporation. All rights reservedContents LUN Chapter Configuring an EMC Boot DeviceAppendix a Third-Party Software Appendix B TroubleshootingProblems and Solutions Index EMC Fibre Channel with QLogic HBAs in Windows Hosts EMC uses the following conventions for notes, cautions, PrefaceDamage to the system or equipment. The caution may apply to Hardware or softwareBold Related Documentation Typographical ConventionsPalatino Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Downloading QLogic Drivers Firmware Verifying Documentation IntroductionInstalling an HBA Check for an Updated HBA Driver Move the jumpers, onto pins 1-2 if not already there Reconfigure the HBA JumperSet the HBA FC-AL Loop ID Installing an HBA Pre-Configured EMC HBA SettingsSettings Advanced Adapter Settings , and Extended Firmware SettingsTo set the first HBA, follow these procedures Configuring Nvram for Stratus ftServersFibre-Down Servers Firmware/BIOSWith Embedded QLogic HBAsExample Flasutil /L /F /N NVRAM23o.DAT To load firmware/BIOS and Nvram settings, typePress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Select have Disk Administrative Tools, Computer ManagementEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device LUN How to Determine I/O Latency and Load on the BootBehavior Boot CrashdumpSave to Disk Configuring a Symmetrix Boot Device From the Host Adapter Settings menu, select Host Adapter From the Configuration Settings menu, select Host AdapterSelect Current Boot Node Name and press Enter Configuration Settings menuBoot Device InstallingWindows OS onto Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Procedure Configuring a CLARiiON Boot DeviceFlowchart Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Requirements Configurations, Revisions Hardware Software RequirementsRequirements, and related documentation TopologiesRequired media includes the following Preparing the Storage SystemMedia Requirements Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts Continue to Preparing the Server on Node NameWhat Next? Physical Connection of Only One SP Port to the Fabric Preparing the ServerSelect Set Boot Controller Order Configuring the HP ProLiant BL20p G2Boot Bios Configuring the HBACTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring Installing AdditionalAdditional Boot Port Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device On the Computer Management window, click Disk Management Trespassing the Boot LUN Using atftrespassStarting a Fresh Installation Boot Time and LUN Availability EMC Symmetrix EMC CLARiiON Replacing a Boot HBAExplanations of Entries How a Server Responds to Failure in the Boot LUN PathStop Error fatal blue screen Indicates host failure Ntosknl Bsod Known IssuesEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager After completing these changes, reboot the host system Veritas Volume Manager 3.x for WindowsEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Solution Problems and SolutionsProblem Contain this correction EMC Support. Windows 2003 driver 8.2.2.20 and later alreadyEMC Primus case emc69308 Direct-connect to EMC CLARiiON A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index