EMC QLA23xx, QLA22xx manual From this point, press S to specify additional devices

Page 40

3

Configuring an EMC Boot Device

7.Some servers use SCSI CD-ROM drives. If your server has a SCSI CD-ROM, repeat steps 5 and 6 to select the driver for the SCSI controller. If your controller is not on the list, obtain the driver on diskette from the vendor.

8.If you want to specify drivers for other devices installed in your system, do so; otherwise press ENTER at the Additional Devices screen to continue with Windows installation.

9.After completing Windows installation, reinstall the QLogic driver using the steps under Installation Procedure for Windows NT Hosts on page 2-15.

Windows 2000 The HP ProLiant BL20p G2 Windows 2000 Installation procedure is described under HP ProLiant BL20p G2 Windows 2000 Installation on page 3-9.

1.Boot the installation CD-ROM. (On some servers, it might be necessary to use the Windows 2000 installation diskettes to start the installation procedure.)

When the installer starts, a message appears at the bottom of the screen, prompting you to press F6 to load any other third-party drivers.

Press F6.

2.After a few moments, the installer stops to let you add additional devices. A screen message will tell you that the setup program cannot determine the type of one or more mass storage devices.

From this point, press S to specify additional devices.

3.Insert the QLogic driver diskette into the drive and press ENTER.

4.Select the model adapter that you have installed from the list that appears. Be sure to choose the correct model series for the HBA you have installed (QLA2300, for example) and press ENTER.

The driver loads and you are brought back to the Additional Devices screen.

5.If you want to specify drivers for other devices installed in your system, do so; otherwise press ENTER at the Additional Devices screen to continue with Windows installation.

6.After completing Windows installation, reinstall the QLogic driver using the steps under Installation Procedure for Windows 2000 and Windows 2003 Hosts on page 2-15.

3-8

EMC Fibre Channel with QLogic HBAs in Windows Hosts

 

 

Image 40
Contents REV A01 August Copyright 2001-2003 EMC Corporation. All rights reserved Trademark InformationContents Chapter Configuring an EMC Boot Device LUNProblems and Solutions Index Appendix B TroubleshootingAppendix a Third-Party Software EMC Fibre Channel with QLogic HBAs in Windows Hosts Preface EMC uses the following conventions for notes, cautions,Damage to the system or equipment. The caution may apply to Hardware or softwarePalatino Related Documentation Typographical ConventionsBold Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Introduction Downloading QLogic Drivers Firmware Verifying DocumentationInstalling an HBA Check for an Updated HBA Driver Reconfigure the HBA Jumper Move the jumpers, onto pins 1-2 if not already thereSet the HBA FC-AL Loop ID Installing an HBA EMC HBA Settings Pre-ConfiguredSettings Advanced Adapter Settings , and Extended Firmware SettingsConfiguring Nvram for Stratus ftServers To set the first HBA, follow these proceduresFirmware/BIOS Fibre-Down ServersWith Embedded QLogic HBAsTo load firmware/BIOS and Nvram settings, type Example Flasutil /L /F /N NVRAM23o.DATPress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Administrative Tools, Computer Management Select have DiskEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device How to Determine I/O Latency and Load on the Boot LUNSave to Disk Boot CrashdumpBehavior Configuring a Symmetrix Boot Device From the Configuration Settings menu, select Host Adapter From the Host Adapter Settings menu, select Host AdapterSelect Current Boot Node Name and press Enter Configuration Settings menuInstalling Boot DeviceWindows OS onto Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Configuring a CLARiiON Boot Device ProcedureFlowchart Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Configurations, Revisions Hardware Software Requirements RequirementsRequirements, and related documentation TopologiesMedia Requirements Preparing the Storage SystemRequired media includes the following Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts What Next? Node NameContinue to Preparing the Server on Preparing the Server Physical Connection of Only One SP Port to the FabricConfiguring the HP ProLiant BL20p G2 Select Set Boot Controller OrderConfiguring the HBA Boot BiosCTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Installing Additional ConfiguringAdditional Boot Port Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device Trespassing the Boot LUN Using atftrespass On the Computer Management window, click Disk ManagementStarting a Fresh Installation Boot Time and LUN Availability Replacing a Boot HBA EMC Symmetrix EMC CLARiiONStop Error fatal blue screen Indicates host failure How a Server Responds to Failure in the Boot LUN PathExplanations of Entries Known Issues Ntosknl BsodEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager Veritas Volume Manager 3.x for Windows After completing these changes, reboot the host systemEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Problem Problems and SolutionsSolution EMC Support. Windows 2003 driver 8.2.2.20 and later already Contain this correctionEMC Primus case emc69308 Direct-connect to EMC CLARiiON A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index