EMC QLA23xx, QLA22xx manual Fibre-Down Servers, With Embedded, QLogic HBAs, Updating, Firmware/BIOS

Page 22

2

Installing and Configuring the HBA Driver

Ignore any steps that pertain to multiple adapters.

4. Shut down the server.

5. Before powering up the server, restore power to the PCI Chassis:

 

 

• For Stratus ftServer 3200 systems, tighten the Phillips-head

 

 

screw that you loosened on the top right of the chassis.

 

 

• For Stratus ftServer 5200 systems, power up the chassis.

 

 

6. Power up the server and proceed to Installing the HBA Driver on

 

 

page 2-14.

 

 

 

 

Fibre-Down Servers

 

Fibre-Down servers have a vendor-specific firmware utility and

with Embedded

 

package that is posted on the QLogic website, in the EMC section. Be

QLogic HBAs

 

sure to use the firmware utility and package that matches your

 

 

server model. You can check for updated firmware on the QLogic

 

 

website. Follow the steps under Downloading QLogic Drivers and

 

 

Firmware on page 2-2.

 

 

 

 

Updating

 

You can update the HBA firmware/BIOS and NVRAM either from

Firmware/BIOS and

 

within a running Windows installation or by booting the server to a

Applying NVRAM

 

DOS command prompt and running the procedure described in this

Settings

 

section.

 

 

 

 

 

 

Current 64-bit systems can be updated only from within Windows 2003 using

 

 

the SANSurfer SANBlade Manager. Refer to QLogic SANSurfer SANBlade

 

 

Manager v2.0.21 on page A-2 for instructions.

 

 

 

 

!

Updating While Running Windows

CAUTION

Do not flash embedded HBAs using the HBA utilities noted in this section. (Refer to Fibre-Down Servers with Embedded QLogic HBAs).

To update while running Windows, refer to QLogic SANSurfer SANBlade Manager v2.0.21 on page A-2.

Stratus ftServers are not supported using the qLogic SANSurfer SANBlade Manager Software or Agents, and should only be updated using the DOS boot diskette. Refer to Updating Using a DOS Boot Diskette.

2-10

EMC Fibre Channel with QLogic HBAs in Windows Hosts

 

 

Image 22
Contents REV A01 August Copyright 2001-2003 EMC Corporation. All rights reserved Trademark InformationContents Chapter Configuring an EMC Boot Device LUNProblems and Solutions Index Appendix B TroubleshootingAppendix a Third-Party Software EMC Fibre Channel with QLogic HBAs in Windows Hosts Damage to the system or equipment. The caution may apply to PrefaceEMC uses the following conventions for notes, cautions, Hardware or softwarePalatino Related Documentation Typographical ConventionsBold Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Introduction Downloading QLogic Drivers Firmware Verifying DocumentationInstalling an HBA Check for an Updated HBA Driver Reconfigure the HBA Jumper Move the jumpers, onto pins 1-2 if not already thereSet the HBA FC-AL Loop ID Installing an HBA Settings EMC HBA SettingsPre-Configured Advanced Adapter Settings , and Extended Firmware SettingsConfiguring Nvram for Stratus ftServers To set the first HBA, follow these proceduresWith Embedded Firmware/BIOSFibre-Down Servers QLogic HBAsTo load firmware/BIOS and Nvram settings, type Example Flasutil /L /F /N NVRAM23o.DATPress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Administrative Tools, Computer Management Select have DiskEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device How to Determine I/O Latency and Load on the Boot LUNSave to Disk Boot CrashdumpBehavior Configuring a Symmetrix Boot Device Select Current Boot Node Name and press Enter From the Configuration Settings menu, select Host AdapterFrom the Host Adapter Settings menu, select Host Adapter Configuration Settings menuWindows OS onto InstallingBoot Device Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Flowchart Configuring a CLARiiON Boot DeviceProcedure Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Requirements, and related documentation Configurations, Revisions Hardware Software RequirementsRequirements TopologiesMedia Requirements Preparing the Storage SystemRequired media includes the following Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts What Next? Node NameContinue to Preparing the Server on Preparing the Server Physical Connection of Only One SP Port to the FabricConfiguring the HP ProLiant BL20p G2 Select Set Boot Controller OrderConfiguring the HBA Boot BiosCTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Additional Boot Port Installing AdditionalConfiguring Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device Trespassing the Boot LUN Using atftrespass On the Computer Management window, click Disk ManagementStarting a Fresh Installation Boot Time and LUN Availability Replacing a Boot HBA EMC Symmetrix EMC CLARiiONStop Error fatal blue screen Indicates host failure How a Server Responds to Failure in the Boot LUN PathExplanations of Entries Known Issues Ntosknl BsodEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager Veritas Volume Manager 3.x for Windows After completing these changes, reboot the host systemEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Problem Problems and SolutionsSolution EMC Primus case emc69308 Direct-connect to EMC CLARiiON EMC Support. Windows 2003 driver 8.2.2.20 and later alreadyContain this correction A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index