EMC QLA23xx, QLA22xx manual From the Configuration Settings menu, select Host Adapter

Page 38

3

Configuring an EMC Boot Device

 

5.

From the Configuration Settings menu, select Host Adapter

 

 

Settings and press ENTER.

 

 

 

6.

From the Host Adapter Settings menu, select Host Adapter

 

 

BIOS and press ENTER to enable it if it is not already enabled.

 

 

 

 

 

 

Refer to EMC HBA Settings on page 2-8 for a table of EMC-configured

 

 

NVRAM settings.

 

 

 

 

 

 

 

 

 

 

7.

Press ESC to exit the Configuration Settings menu.

 

 

8.

From the Configuration Settings menu, select Selectable Boot

 

 

Settings and press ENTER.

 

 

 

9.

From the Selectable Boot Settings menu, select Selectable Boot

 

 

Device and press ENTER to enable it if it is not already enabled.

 

10.

Select Current Boot Node Name and press ENTER.

 

 

 

The adapter scans for attached storage devices, and displays them

 

 

on the screen.

 

 

 

 

 

11.

Choose the storage array port from which you wish to boot. Its

 

 

entry will be similar to the following:

 

 

 

 

 

 

 

ID

VENDOR

PRODUCT

REV

NODE NAME

Port ID

12

EMC

 

SYMMETRIX

5566

50060482BFD06C02

0000E4

 

 

 

 

 

 

Select your boot device and press ENTER.

 

 

 

A list of LUNs will appear in a new window. Select the LUN from

 

 

which you wish to boot and press ENTER.

 

 

12.

Press ESC at the Selectable Boot Settings menu to return to the

 

 

Configuration Settings menu.

 

 

 

13.

Press ESC at the Configuration Settings menu to return to the

 

 

Fast!UTIL Options menu.

 

 

 

 

Select Save Changes and press ENTER.

 

 

14.

Press ESC to exit Fast!UTIL.

 

 

 

15.

Reboot the host.

 

 

 

 

3-6

EMC Fibre Channel with QLogic HBAs in Windows Hosts

 

 

Page 37 Page 39
Image 38
Page 37 Page 39
Contents REV A01 August Copyright 2001-2003 EMC Corporation. All rights reserved Trademark InformationContents Chapter Configuring an EMC Boot Device LUNAppendix a Third-Party Software Appendix B TroubleshootingProblems and Solutions Index EMC Fibre Channel with QLogic HBAs in Windows Hosts Damage to the system or equipment. The caution may apply to PrefaceEMC uses the following conventions for notes, cautions, Hardware or softwareBold Related Documentation Typographical ConventionsPalatino Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Introduction Downloading QLogic Drivers Firmware Verifying DocumentationInstalling an HBA Check for an Updated HBA Driver Reconfigure the HBA Jumper Move the jumpers, onto pins 1-2 if not already thereSet the HBA FC-AL Loop ID Installing an HBA Settings EMC HBA SettingsPre-Configured Advanced Adapter Settings , and Extended Firmware SettingsConfiguring Nvram for Stratus ftServers To set the first HBA, follow these proceduresWith Embedded Firmware/BIOSFibre-Down Servers QLogic HBAsTo load firmware/BIOS and Nvram settings, type Example Flasutil /L /F /N NVRAM23o.DATPress the Down Arrow until you select Data Rate then press EMC HBA Settings Installing the HBA Driver Administrative Tools, Computer Management Select have DiskEMC Fibre Channel with QLogic HBAs in Windows Hosts Double-click the Scsi & RAID Controllers icon EMC Fibre Channel with QLogic HBAs in Windows Hosts Upgrading to Windows 2003 from Windows 2000 or Windows NT EMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring an EMC Boot Device Configuring an EMC Boot Device How to Determine I/O Latency and Load on the Boot LUNBehavior Boot CrashdumpSave to Disk Configuring a Symmetrix Boot Device Select Current Boot Node Name and press Enter From the Configuration Settings menu, select Host AdapterFrom the Host Adapter Settings menu, select Host Adapter Configuration Settings menuWindows OS onto InstallingBoot Device Windows NTFrom this point, press S to specify additional devices HP ProLiant BL20p G2 Windows Installation Flowchart Configuring a CLARiiON Boot DeviceProcedure Installation procedure includes steps you must follow in aConfiguring a CLARiiON Boot Device Requirements, and related documentation Configurations, Revisions Hardware Software RequirementsRequirements TopologiesRequired media includes the following Preparing the Storage SystemMedia Requirements Press ESC to return to the previous menu Configuring a CLARiiON Boot Device EMC Fibre Channel with QLogic HBAs in Windows Hosts Continue to Preparing the Server on Node NameWhat Next? Preparing the Server Physical Connection of Only One SP Port to the FabricConfiguring the HP ProLiant BL20p G2 Select Set Boot Controller OrderConfiguring the HBA Boot BiosCTRL-Q G2 Windows 2000 OS Installation on Windows Licensing Agreement appears HP ProLiant BL20p G2 Windows 2000 OS Installation Verifying HBA Driver Digital Signature Installation EMC Fibre Channel with QLogic HBAs in Windows Hosts Additional Boot Port Installing AdditionalConfiguring Navisphere HostEMC Fibre Channel with QLogic HBAs in Windows Hosts Configuring a CLARiiON Boot Device Trespassing the Boot LUN Using atftrespass On the Computer Management window, click Disk ManagementStarting a Fresh Installation Boot Time and LUN Availability Replacing a Boot HBA EMC Symmetrix EMC CLARiiONExplanations of Entries How a Server Responds to Failure in the Boot LUN PathStop Error fatal blue screen Indicates host failure Known Issues Ntosknl BsodEMC Fibre Channel with QLogic HBAs in Windows Hosts Third-Party Software QLogic SANSurfer SANBlade Manager Veritas Volume Manager 3.x for Windows After completing these changes, reboot the host systemEMC Fibre Channel with QLogic HBAs in Windows Hosts Troubleshooting Solution Problems and SolutionsProblem EMC Primus case emc69308 Direct-connect to EMC CLARiiON EMC Support. Windows 2003 driver 8.2.2.20 and later alreadyContain this correction A host may log a message noting that disk has reached aEMC Fibre Channel with QLogic HBAs in Windows Hosts Index Index
Top Page Image Contents