Extron electronic MAV 84, MAV 88, MAV 44 Audio input and output connections audio/video models

Page 21

Audio input and output connections (audio/video models)

The audio level for each input can be individually set, via the front panel or RS-232, to ensure that the level on the output does not vary from input to input. See chapter 3, “Operation”, and chapter 4, “Remote Operation” for details.

By default, the audio follows the video switch. Audio breakaway, which is commanded via the front panel, under RS-232 control via the SIS or Windows- based control program, or optional IR 501 control, allows you to select from any one of the audio input sources. For details, see chapter 3, “Operation”, and chapter 4, “Remote Operation”, and refer to the IR 501 Small Matrix IR Remote Control User’s Guide.

5Balanced or unbalanced audio input connections (captive screw audio connector [A] models only) — Each input has a 3.5 mm, 5-pole captive screw connector for balanced or unbalanced stereo audio input. Connectors are included with each MAV AV captive screw connector switcher, but you must supply the audio cable. See figure 2-4 to wire a connector for the appropriate input type and impedance level. High impedance is generally over 5 k ohms.

Figure 2-4 shows two methods of wiring the captive screw audio connectors for input and figure 2-6 shows two methods of wiring the connectors for output. A mono audio connector consists of the tip and sleeve. A stereo audio connector consists of the tip, ring, and sleeve. If you are wiring a captive screw connector from an existing unbalanced audio cable, the white insulated wire is typically the left channel (tip) and the red insulated wire is typically the right channel (sleeve). There is no reliable standard for existing balanced audio cables.

 

Tip

L

 

Sleeve

 

 

 

Tip

R

 

Sleeve

 

 

3/16” (5 mm) Max. Unbalanced Stereo Input

Do not tin the wires!

 

(high impedance)

Tip

L

Ring

 

Sleeve (s)

 

Tip

R

Ring

 

Balanced Stereo Input

(high impedance)

Figure 2-4 — Captive screw connector wiring for audio inputs

The length of exposed wires is critical. The ideal length is 3/16” (5 mm).

If the stripped section of wire is longer than 3/16”, the exposed wires may touch, causing a short circuit between them.

If the stripped section of wire is shorter than 3/16”, wires can be easily pulled out even if tightly fastened by the captive screws.

6RCA connector audio inputs (RCA audio connector [A RCA] models only) — Each input has a pair (left and right) of RCA connectors for unbalanced stereo audio input (figure 2-5).

Tip (Signal)

Right Channel

(Red Jacket)

Tip (+)

Sleeve (Gnd )

Left Channel

Sleeve ( )

(White Jacket)

 

Figure 2-5 — RCA connector wiring

MAV 44 / 48 / 84 / 88 Matrix Switchers • Installation

2-5

Image 21
Contents MAV 44 / 48 / 84 / 88 Series Matrix SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolFCC Class a Notice Page MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start QS-1 Unbalanced stereo audio inputs toStereo audio devices to the output Saving or recalling a preset Quick Start MAV Series AV Matrix Switchers, cont’dPowering on QS-2 MAV 44 / 48 / 84 / 88 Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents Iii Iv MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents One About the Switchers MAV 44 / 48 / 84 / 88 Matrix Switchers IntroductionIntroductiontroduction, cont’d Video features FeaturesCommon features Audio featuresIntroduction, cont’d Any input to any or all outputsMAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Introduction, cont’d Two Mounting the Switcher Installationstallation, cont’dRack mounting the switcher Tabletop useMounting the switcher Furniture mounting the switcherInstallation, cont’d Cabling and Rear Panel ViewsVideo input and output connections Audio input and output connections audio/video models Captive screw connector wiring for audio inputsRemote connection Captive screw connector wiring for audio outputExternal sync connection Shows a basic external sync configurationMultiple device external sync connection example Power connectionThree Front Panel Controls and Indicators MAV 44 / 48 / 84 / 88 Matrix Switchers OperationOperationeration, cont’d Power/audio/data LED and infrared sensor Power/data/audio LEDDefinitions Input and output selection controls and indicators Operation, cont’dControl buttons and LEDs Video/+dB LED and Audio/-dB LED Audio Setup buttonOperations Powering up the switcherCreating a set of ties Press and release the Input 5 button figure Example 1 Create a set of video and audio tiesThis example assumes that you have performed example Example 2 Add a video tie to a set of video and audio ties11 Select the output Press and release the Output 4 button figure Example 3 Remove a tie from a set of tiesVideo Viewing the configuration19 Select video and audio Example 4 View ties by selecting an inputExample 5 View ties by selecting outputs Press and release the I/O button figure24 Select an output 26 Deselect video to view audio ties only Using presetsPreset 2 Preset Example 6 Save a preset29 Select Recall Preset mode, MAV Example 7 Recall a presetConsumer VCR Audio Inputs Adjusting input audio gain and attenuationTo exit Audio Setup mode. The Audio Setup LED turns off Seconds Example 8 Adjust the input audio gain+2 dB 34 Adjust the input audio levelPress and release the and buttons simultaneously figure Resetting audio gain single inputSetting the output audio level Resetting audio gain all inputsClearing all ties and presets Front panel security lockout Executive modeMemory 43 System reset to factory defaultsTroubleshooting Optimizing the Audio Audio/Video SwitchersWorksheet example 1 System equipment Worksheets45 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration46 Worksheet example 3 Test configuration Worksheet example 3 Test configurationOutput destinations Configuration worksheetOperation, cont’d Four MAV 44 / 48 / 84 / 88 Matrix Switchers Remote Operation Host-to-Switcher instructionsRemoteOperation,cont’d Simple Instruction Set ControlSwitcher-initiated messages Using the command/response table Switcher error responsesSymbol definitions Remote Operation, cont’dCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands cont’d IR receiver enable Resets Firmware upload Turn on the echo function Loading firmware using an SIS commandSelect the firmware upgrade file Installing the software Matrix Switchers Control ProgramOverview Using the softwareExtron Matrix Switchers Control Program window blank 11 Determining the firmware version Updating the firmware12 Open window, version 2.xx firmware files 13 Open window, version 1.xx firmware files Windows buttons, drop boxes, and the trash can Windows menus File menuTools menu Preferences menu Audio-input Configuration selection18 Ties shown as crosspoints Master-Reset selectionUsing the help system Using Emulation modeAAppendix a Specifications SpecificationsandandPartPartNumbers,Numberscont’dSync composite video and S-video models Audio output audio models Specifications and Part Numbers, cont’dControl/remote switcher Replacement parts MAV Series AV switchersPart Numbers Included partsCables Optional accessoriesPre-cut cables Assorted connectors BNC connectorsVideo Cable Composite video CableAsia Japan Extron’s WarrantyExtron Electronics, Europe Beeldschermweg 6C