Extron electronic MAV 44, MAV 88, MAV 84, MAV 48 manual Press and release the I/O button figure

Page 38

Operation, cont’d

3. Press and release the I/O button (figure 3-21).

Press the button to deselect audio.

I/O

The video LED lights

when video is selected. VID +dB

The audio LED is off AUD -dBwhen audio is deselected.

OUTPUTS

1

2

3

4

5

6

7

8

The Output 1, Output 3, Output 4, and Output 8 LEDs light to indicate the video ties created in example 1 and 2.

Figure 3-21 — Deselect audio to view video only

4. Press and release the I/O button (figure 3-22).

Press the button to deselect video and select audio.

I/O

The video LED is off

when video is deselected. VID +dB

The audio LED lights AUD -dBwhen audio is selected.

OUTPUTS

1

2

3

4

5

6

7

8

The Output 3 and Output 8 LEDs light to indicate the audio ties created in example 1. (Example 2 created a video only tie. Example 3 deleted an audio tie.)

Figure 3-22 — Deselect video and select audio to view audio only

5. Allow the 5-second input and output button timeout to deselect the input.

Example 5: View ties by selecting outputs

The following steps show an example of viewing the video and audio, audio-only, and video-only ties in the current configuration by selecting various outputs. The example shows the front panel indications that result from your actions.

This example assumes that you have performed example 1, example 2, and example 3.

1. Audio/video switchers only — Select both video and audio for viewing (figure 3-23).

Press the button to cycle through the selections.

I/O

The video LED lights when video is selected. VID

The audio LED lights when audio is selected. AUD

Figure 3-23 — Select video and audio

Ensure that no input button is selected before you select an output button. If an input button is selected, the indications will not be as described and you may inadvertently establish potential ties that could be created by pressing the Enter button.

If you do inadvertently establish a potential tie by selecting an input and output button, do not press the Enter button. Allow the 5-second timeout to deselect all input and output buttons.

3-14 MAV 44 / 48 / 84 / 88 Matrix Switchers • Operation

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Matrix Switchers MAV 44 / 48 / 84 / 88 SeriesSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolFCC Class a Notice Page Stereo audio devices to the output MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start QS-1Unbalanced stereo audio inputs to Powering on Quick Start MAV Series AV Matrix Switchers, cont’dSaving or recalling a preset QS-2 MAV 44 / 48 / 84 / 88 Matrix Switchers Quick StartTable of Contents Table of Contents, cont’d MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents Iii Iv MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents One Introductiontroduction, cont’d About the SwitchersMAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Features Video featuresIntroduction, cont’d Audio featuresCommon features Any input to any or all outputsMAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Introduction, cont’d Two Rack mounting the switcher Installationstallation, cont’dMounting the Switcher Tabletop useFurniture mounting the switcher Mounting the switcherVideo input and output connections Installation, cont’dCabling and Rear Panel Views Captive screw connector wiring for audio inputs Audio input and output connections audio/video modelsCaptive screw connector wiring for audio output Remote connectionShows a basic external sync configuration External sync connectionPower connection Multiple device external sync connection exampleThree Operationeration, cont’d Front Panel Controls and IndicatorsMAV 44 / 48 / 84 / 88 Matrix Switchers Operation Definitions Power/audio/data LED and infrared sensorPower/data/audio LED Control buttons and LEDs Input and output selection controls and indicatorsOperation, cont’d Audio Setup button Video/+dB LED and Audio/-dB LEDPowering up the switcher OperationsCreating a set of ties Example 1 Create a set of video and audio ties Press and release the Input 5 button figureExample 2 Add a video tie to a set of video and audio ties This example assumes that you have performed example11 Select the output Example 3 Remove a tie from a set of ties Press and release the Output 4 button figureViewing the configuration VideoExample 4 View ties by selecting an input 19 Select video and audioPress and release the I/O button figure Example 5 View ties by selecting outputs24 Select an output Using presets 26 Deselect video to view audio ties onlyExample 6 Save a preset Preset 2 PresetExample 7 Recall a preset 29 Select Recall Preset mode, MAVAdjusting input audio gain and attenuation Consumer VCR Audio InputsTo exit Audio Setup mode. The Audio Setup LED turns off Example 8 Adjust the input audio gain Seconds34 Adjust the input audio level +2 dBResetting audio gain single input Press and release the and buttons simultaneously figureResetting audio gain all inputs Setting the output audio levelFront panel security lockout Executive mode Clearing all ties and presets43 System reset to factory defaults MemoryOptimizing the Audio Audio/Video Switchers TroubleshootingWorksheets Worksheet example 1 System equipmentWorksheet example 2 Daily configuration 45 Worksheet example 2 Daily configurationWorksheet example 3 Test configuration 46 Worksheet example 3 Test configurationConfiguration worksheet Output destinationsOperation, cont’d Four RemoteOperation,cont’d Host-to-Switcher instructionsMAV 44 / 48 / 84 / 88 Matrix Switchers Remote Operation Simple Instruction Set ControlSwitcher-initiated messages Symbol definitions Switcher error responsesUsing the command/response table Remote Operation, cont’dCommand/response table for SIS commands Command Ascii Command Response Additional descriptionCommand/response table for SIS commands cont’d IR receiver enable Resets Firmware upload Loading firmware using an SIS command Turn on the echo functionSelect the firmware upgrade file Matrix Switchers Control Program Installing the softwareUsing the software OverviewExtron Matrix Switchers Control Program window blank Updating the firmware 11 Determining the firmware version12 Open window, version 2.xx firmware files 13 Open window, version 1.xx firmware files Windows buttons, drop boxes, and the trash can Tools menu Windows menusFile menu Audio-input Configuration selection Preferences menuMaster-Reset selection 18 Ties shown as crosspointsUsing Emulation mode Using the help systemAAppendix a SpecificationsandandPartPartNumbers,Numberscont’d SpecificationsSync composite video and S-video models Specifications and Part Numbers, cont’d Audio output audio modelsControl/remote switcher Part Numbers MAV Series AV switchersReplacement parts Included partsOptional accessories CablesVideo Cable Assorted connectors BNC connectorsPre-cut cables Composite video CableExtron’s Warranty Asia JapanExtron Electronics, Europe Beeldschermweg 6C
Top Page Image Contents