Extron electronic MAV 48, MAV 88, MAV 84, MAV 44 manual Creating a set of ties

Page 31

2.

Plug in all system components and turn on the input devices (such as DVD

 

players, laserdisc players, VCRs, and DSS receivers) and the output devices.

3.

Set the input devices to output video using each device’s own operating

 

instructions.

4.

Create a tie (see below). The selected input image should appear at the

 

selected output. If no image appears, see “Troubleshooting”, on page 3-27.

Creating a set of ties

You can create a set of ties, changing the current configuration, by using the front panel buttons. Change the current configuration as follows:

1.

On audio/video switchers, select to configure video, audio, or both by

 

pressing the I/O button as necessary.

2.

Select the desired input and output(s) by pressing the input and output

 

buttons.

3.

Press and release the Enter button.

4.

Repeat steps 1 through 3 to create additional ties until the desired

 

configuration is complete.

• Only one video input and one audio input can be tied to an output.

If a tie is made between an input and an output, and the selected output was previously tied to another input, the older tie is broken in favor of the newer tie.

Output LEDs light when an input is selected to indicate current ties. Press and release the associated output buttons to clear unwanted outputs.

If, when you are configuring video and audio ties, the Audio LED blinks and the Video LED is on after you have selected an input or output, the LEDs indicate audio breakaway, meaning that the audio ties are not the same as the video ties for that input.

If an input with no tie is selected, only that input’s LED lights.

As each output is selected, the associated output LED blinks to indicate a tentative tie until you press the Enter button or the 5-second timeout expires. LEDs for output(s) that were already tied to the input light steadily. Outputs that are already tied can be left on, along with new blinking selections, or toggled off by pressing the associated output button.

If you inadvertently press the wrong input or output button, wait approximately 5 seconds. The input and output button selections time out and are abandoned.

MAV 44 / 48 / 84 / 88 Matrix Switchers • Operation

3-7

Image 31
Contents MAV 44 / 48 / 84 / 88 Series Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class a Notice Page Unbalanced stereo audio inputs to MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start QS-1Stereo audio devices to the output QS-2 MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start Quick Start MAV Series AV Matrix Switchers, cont’dSaving or recalling a preset Powering onTable of Contents Table of Contents, cont’d MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents Iii Iv MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents One MAV 44 / 48 / 84 / 88 Matrix Switchers Introduction About the SwitchersIntroductiontroduction, cont’d Video features FeaturesAny input to any or all outputs Audio featuresCommon features Introduction, cont’dMAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Introduction, cont’d Two Tabletop use Installationstallation, cont’dMounting the Switcher Rack mounting the switcherMounting the switcher Furniture mounting the switcherCabling and Rear Panel Views Installation, cont’dVideo input and output connections Audio input and output connections audio/video models Captive screw connector wiring for audio inputsRemote connection Captive screw connector wiring for audio outputExternal sync connection Shows a basic external sync configurationMultiple device external sync connection example Power connectionThree MAV 44 / 48 / 84 / 88 Matrix Switchers Operation Front Panel Controls and IndicatorsOperationeration, cont’d Power/data/audio LED Power/audio/data LED and infrared sensorDefinitions Operation, cont’d Input and output selection controls and indicatorsControl buttons and LEDs Video/+dB LED and Audio/-dB LED Audio Setup buttonOperations Powering up the switcherCreating a set of ties Press and release the Input 5 button figure Example 1 Create a set of video and audio tiesThis example assumes that you have performed example Example 2 Add a video tie to a set of video and audio ties11 Select the output Press and release the Output 4 button figure Example 3 Remove a tie from a set of tiesVideo Viewing the configuration19 Select video and audio Example 4 View ties by selecting an inputExample 5 View ties by selecting outputs Press and release the I/O button figure24 Select an output 26 Deselect video to view audio ties only Using presetsPreset 2 Preset Example 6 Save a preset29 Select Recall Preset mode, MAV Example 7 Recall a presetConsumer VCR Audio Inputs Adjusting input audio gain and attenuationTo exit Audio Setup mode. The Audio Setup LED turns off Seconds Example 8 Adjust the input audio gain+2 dB 34 Adjust the input audio levelPress and release the and buttons simultaneously figure Resetting audio gain single inputSetting the output audio level Resetting audio gain all inputsClearing all ties and presets Front panel security lockout Executive modeMemory 43 System reset to factory defaultsTroubleshooting Optimizing the Audio Audio/Video SwitchersWorksheet example 1 System equipment Worksheets45 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration46 Worksheet example 3 Test configuration Worksheet example 3 Test configurationOutput destinations Configuration worksheetOperation, cont’d Four Simple Instruction Set Control Host-to-Switcher instructionsMAV 44 / 48 / 84 / 88 Matrix Switchers Remote Operation RemoteOperation,cont’dSwitcher-initiated messages Remote Operation, cont’d Switcher error responsesUsing the command/response table Symbol definitionsCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands cont’d IR receiver enable Resets Firmware upload Turn on the echo function Loading firmware using an SIS commandSelect the firmware upgrade file Installing the software Matrix Switchers Control ProgramOverview Using the softwareExtron Matrix Switchers Control Program window blank 11 Determining the firmware version Updating the firmware12 Open window, version 2.xx firmware files 13 Open window, version 1.xx firmware files Windows buttons, drop boxes, and the trash can File menu Windows menusTools menu Preferences menu Audio-input Configuration selection18 Ties shown as crosspoints Master-Reset selectionUsing the help system Using Emulation modeAAppendix a Specifications SpecificationsandandPartPartNumbers,Numberscont’dSync composite video and S-video models Audio output audio models Specifications and Part Numbers, cont’dControl/remote switcher Included parts MAV Series AV switchersReplacement parts Part NumbersCables Optional accessoriesComposite video Cable Assorted connectors BNC connectorsPre-cut cables Video CableAsia Japan Extron’s WarrantyExtron Electronics, Europe Beeldschermweg 6C