Extron electronic MAV 48, MAV 88, MAV 84, MAV 44 manual IR receiver enable

Page 63

Command/response table for SIS commands (cont’d)

Command	ASCII Command	Response	Additional description
	(host to switcher)	(switcher to host)
IR receiver enable

Enable IR receiver	0*65#	IRdisable*0	Enable the IR receiver (allow
			control by the IR 501).
Disable IR receiver	1*65#	IRdisable*1	Disable the IR receiver (do not
			allow control by the IR 501).

Read IR receiver enable

65#

X10	0= enable, 1 = disable (default).

Global presets

Save current configuration as preset		,	Spr		Command character is a comma.
	X11			X11
Example:	8,		Spr08		Save current ties as preset 8.
Recall a preset		.	Rpr		Command character is a period.
	X11			X11
Example:	5.		Rpr05		Recall preset 5, which becomes
					the current configuration.

View global preset configuration

EscX11 VC

X2 1• X2 2• X2 3•...• X2 n•Vid• X2 1• X2 2• X2 3•...• X2 n•Aud

n is the highest output number for this model switcher. Show preset X11 ’s video and audio configuration. Show the video input tied to n sequential outputs and then the audio input tied to n sequential outputs.

Response description:	Video input # (I#) assigned to Output # (O#1)•I# assigned to O#2...I# assigned to O#8•Vid•
	Audio I# assigned to O#1•I# assigned to O#2...I# assigned to O#8•Aud

Example (MAV 88 AV):

Esc 4VC

Input 5 video tied to output 2 No tied input Audio input 8 tied to output 5

Response = tied input: 6•5•6•8•3•3•1•0•Vid•8•1•1•1•8•8•8•8•Aud


Output: 1		2		3		4		5		6		7		8		1		2		3		4		5		6		7		8

Each position shown in the response is an output: left = output 1, right = output 8. The number in each position is the input tied to that output. Global preset 4 makes the following ties:

Video — Input 6 is tied to outputs 1 and 3; input 5 to output 2; input 8 to output 4; input 3 to outputs 5 and 6; and input 1 to output 7. No input is tied to output 8.

Audio — Input 8 is tied to outputs 1 and outputs 5 through 8; input 1 to outputs 2 through 4.

Example (MAV 44 V):

Esc

4VC

Input 1 tied to output 2

Response = tied input: 1•1•0•2•Vid

Output: 1 1 1 1

Front panel security lockout (Executive mode)

Lock front panel	1X	Exe1		Enable executive mode.
Unlock front panel	0X	Exe0		Disable executive mode.
Read front panel lockout status	X	X8		1= executive mode on,
				0 = executive mode off.

MAV 44 / 48 / 84 / 88 Matrix Switchers • Remote Operation

4-7

Image 63

Contents MAV 44 / 48 / 84 / 88 Series Matrix SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class a Notice Page MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start QS-1 Unbalanced stereo audio inputs toStereo audio devices to the output QS-2 MAV 44 / 48 / 84 / 88 Matrix Switchers Quick Start Quick Start MAV Series AV Matrix Switchers, cont’dSaving or recalling a preset Powering onTable of Contents Table of Contents, cont’d MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents Iii Iv MAV 44 / 48 / 84 / 88 Matrix Switchers Table of Contents One About the Switchers MAV 44 / 48 / 84 / 88 Matrix Switchers IntroductionIntroductiontroduction, cont’d Video features FeaturesAny input to any or all outputs Audio featuresCommon features Introduction, cont’dMAV 44 / 48 / 84 / 88 Matrix Switchers Introduction Introduction, cont’d Two Tabletop use Installationstallation, cont’dMounting the Switcher Rack mounting the switcherMounting the switcher Furniture mounting the switcherInstallation, cont’d Cabling and Rear Panel ViewsVideo input and output connections Audio input and output connections audio/video models Captive screw connector wiring for audio inputsRemote connection Captive screw connector wiring for audio outputExternal sync connection Shows a basic external sync configurationMultiple device external sync connection example Power connectionThree Front Panel Controls and Indicators MAV 44 / 48 / 84 / 88 Matrix Switchers OperationOperationeration, cont’d Power/audio/data LED and infrared sensor Power/data/audio LEDDefinitions Input and output selection controls and indicators Operation, cont’dControl buttons and LEDs Video/+dB LED and Audio/-dB LED Audio Setup buttonOperations Powering up the switcherCreating a set of ties Press and release the Input 5 button figure Example 1 Create a set of video and audio tiesThis example assumes that you have performed example Example 2 Add a video tie to a set of video and audio ties11 Select the output Press and release the Output 4 button figure Example 3 Remove a tie from a set of tiesVideo Viewing the configuration19 Select video and audio Example 4 View ties by selecting an inputExample 5 View ties by selecting outputs Press and release the I/O button figure24 Select an output 26 Deselect video to view audio ties only Using presetsPreset 2 Preset Example 6 Save a preset29 Select Recall Preset mode, MAV Example 7 Recall a presetConsumer VCR Audio Inputs Adjusting input audio gain and attenuationTo exit Audio Setup mode. The Audio Setup LED turns off Seconds Example 8 Adjust the input audio gain+2 dB 34 Adjust the input audio levelPress and release the and buttons simultaneously figure Resetting audio gain single inputSetting the output audio level Resetting audio gain all inputsClearing all ties and presets Front panel security lockout Executive modeMemory 43 System reset to factory defaultsTroubleshooting Optimizing the Audio Audio/Video SwitchersWorksheet example 1 System equipment Worksheets45 Worksheet example 2 Daily configuration Worksheet example 2 Daily configuration46 Worksheet example 3 Test configuration Worksheet example 3 Test configurationOutput destinations Configuration worksheetOperation, cont’d Four Simple Instruction Set Control Host-to-Switcher instructionsMAV 44 / 48 / 84 / 88 Matrix Switchers Remote Operation RemoteOperation,cont’dSwitcher-initiated messages Remote Operation, cont’d Switcher error responses Using the command/response table Symbol definitionsCommand Ascii Command Response Additional description Command/response table for SIS commandsCommand/response table for SIS commands cont’d IR receiver enable Resets Firmware upload Turn on the echo function Loading firmware using an SIS commandSelect the firmware upgrade file Installing the software Matrix Switchers Control ProgramOverview Using the softwareExtron Matrix Switchers Control Program window blank 11 Determining the firmware version Updating the firmware12 Open window, version 2.xx firmware files 13 Open window, version 1.xx firmware files Windows buttons, drop boxes, and the trash can Windows menus File menuTools menu Preferences menu Audio-input Configuration selection18 Ties shown as crosspoints Master-Reset selectionUsing the help system Using Emulation modeAAppendix a Specifications SpecificationsandandPartPartNumbers,Numberscont’dSync composite video and S-video models Audio output audio models Specifications and Part Numbers, cont’dControl/remote switcher Included parts MAV Series AV switchersReplacement parts Part NumbersCables Optional accessoriesComposite video Cable Assorted connectors BNC connectorsPre-cut cables Video CableAsia Japan Extron’s WarrantyExtron Electronics, Europe Beeldschermweg 6C