Extron electronic XTP T UWP 202 manual Installing the Metal Junction Box or Mud Ring

Page 11

4.Route and connect cables to the rear and side panel connectors (see Rear and Side Panel Connectors on page 7).

5.Mount the XTP T UWP 202 to the mud ring or metal junction box (see Mounting the XTP T UPW 202 on page 9).

6.Connect inputs to the front panel connectors (see Front Panel Connections on page 10).

7.Supply power to all connected devices.

Installing the Metal Junction Box or Mud Ring

Cutting an Opening in the Mounting Surface

1.Using an appropriate template or the mounting enclosure as a guide, mark the area of the wall with a soft pencil that will be cut (for the provided mud ring, see Mounting Template on page 40).

NOTE: Check with the manufacturer of the metal junction box for specific installation requirements.

2.Use a jigsaw or small hand saw to carefully cut away the material within the guidelines drawn in step 1.

NOTE: If using a template or the mud ring as a guide for cutting the hole in drywall, cut inside the guidelines to maximize the contact the mud ring makes with the drywall.

4.If using a mud ring in a wall with insulation inside, remove at least 6 inches of the insulation in all directions around the cutout.

NOTE: If a wall stud interferes with removing 6 inches of insulation around the cutout, remove the insulation between the cutout and wall stud.

5.Check the size of the opening by laying the mud ring or metal junction box against it. The mounting device should fit snugly in the opening.

6.If needed, use a saw, file, or sandpaper to enlarge the hole.

CAUTION: Risk of personal injury. Smooth the edges of the opening to avoid personal injury during installation.

ATTENTION: Smooth the edges of the opening to avoid damage to the mounting device or the cables.

XTP T UWP 202 Wallplate Transmitter • Installation and Operation

5

Page 10 Page 12
Image 11
Page 10 Page 12
Contents XTP T UWP Safety Instructions Registered Trademarks FCC Class a NoticeNotifications Specifications AvailabilitySoftware Commands Conventions Used in this GuideContents XTP T UWP 202 Wallplate Transmitter Contents About the XTP T UWP IntroductionAbout this Guide Typical Point-to-Point Application Diagram LAN Model Shown Key FeaturesXTP T UWP 202 Wallplate Transmitter Introduction Installation Overview Installation OperationCutting an Opening in the Mounting Surface Installing the Metal Junction Box or Mud RingInstalling the Mud Ring with Backing Clips Installing the Mud RingXTP output connector RS-232 and IR Over XTP connector Rear and Side Panel ConnectorsInstalling a UL Listed Metal Junction Box RS-232 IR XTP T UWP Mounting the XTP T UWPWiring a TRS Connector for Audio Front Panel ConnectorsAudio Present Making ConnectionsHdmi Connection Selected Hdmi Embedded Analog Audio Audio Sent Over XTPCable recommendations TP Cable Termination and RecommendationsSupported cables RS-232 and IR Over XTP Communication Wiring the RS-232 and IR Over XTP ConnectorLocal power Power ConnectionDirect power from an XTP matrix switcher Remote powerPower injector Operation IndicatorsMode Reset ModesReset Mode Summary Mode Activation Result Purpose/Notes Factory ResetHost-to-Device and Device-to-Host Communication SIS Configuration ControlHost Device Connection SIS Programming GuideSymbol Definitions Error ResponsesUsing the Command and Response Tables for SIS Commands Audio Configuration Commands Command and Response Tables for SIS CommandsInput Commands Preset Commands Picture Adjustment Commands Analog OnlyTest pattern Edid Commands Advanced Configuration CommandsFactory defaults Hdcp authorized device Hdmi input onlyInstalling the XTP System Configuration Software XTP System Configuration SoftwareConnections Using the XTP System Configuration SoftwareExit Top MenuFile menu DisconnectConfirm Disconnect Dialog Box Update FirmwareExtron Website Help menuAbout the Software HelpAV Controls panel Device SettingsInput/Output Tab Input/Output tabAnalog Video tab Image Settings panelInput Presets panel Input format panel Audio tabGeneral tab Auto-input Switching panelFactory reset Audio Information section Signal Information sectionDevice Information panel General Information sectionTo assign Edid to all inputs Edid MinderAssign Edid To assign Edid to selected inputsEdid filters Import EdidSave output Edid Set favorite EdidDownloading Extron Firmware Loader Reference InformationUpdating Firmware with Firmware Loader Navigating to Firmware Loader Installing Firmware LoaderDownloading Firmware from the Extron Website Downloading FirmwareAdd Device... Dialog Box Installing Firmware with Firmware LoaderMounting Template for 2-gang Mud Rings Mounting TemplateExtron Warranty

XTP T UWP 202 specifications

The Extron XTP T UWP 202 is a state-of-the-art, two-gang wallplate transmitter designed for seamless integration into professional AV systems. As part of the XTP system by Extron, it leverages advanced technologies to ensure high-quality signal distribution over long distances, supporting both digital and analog video formats.

One of the standout features of the XTP T UWP 202 is its ability to transmit HDMI, along with audio and control signals, through a single CATx cable. This capability significantly simplifies installation and reduces cable clutter, making it an ideal choice for modern classrooms, conference rooms, and other professional environments. The wallplate connects directly to the XTP CrossPoint matrix switchers, allowing users to take advantage of centralized signal management.

The XTP T UWP 202 supports resolutions up to 4K@60Hz, covering a broad range of applications that require high-definition video output. The device is also equipped with EDID (Extended Display Identification Data) management, which guarantees optimal signal delivery by enabling automatic communication with the receiving display.

Another important aspect of the XTP T UWP 202 is its integrative capabilities. The wallplate includes a USB input for easy access to data sources, enhancing the overall connectivity of the AV system. Additionally, it supports Control Network, allowing integration with various control systems to manage connected devices effortlessly.

The design of the XTP T UWP 202 is user-friendly, featuring an intuitive layout that ensures ease of use for operators. The robust construction and sleek aesthetic allow it to blend seamlessly into any wall, while the included customizable labeling options help identify input sources clearly.

Moreover, the XTP T UWP 202 is equipped with anti-jitter technology, which helps to maintain signal integrity and reduces the chances of video artifacts, ensuring a reliable performance.

In summary, the Extron XTP T UWP 202 combines advanced transmission technology with high-definition video support and integrative features, making it a vital component for any professional AV installation. Its user-friendly design, combined with robust functionality, positions it as an excellent choice for users looking to optimize their AV experience.
Top Page Image Contents