Extron electronic XTP T UWP 202 manual Front Panel Connectors, Wiring a TRS Connector for Audio

Page 16

Front Panel Connectors

A

D

PWR HDCP HDMI

VGA

 

HDMI IN

RESET

AUDIO IN

 

AUDIO

B

 

CLIP

 

AUTO

VGA IN

 

 

 

SWITCH

 

LAN

 

C

 

CONFIG

 

 

 

E

A B C

HDMI input connector Analog audio input connector Analog video input connector

D E

LAN connector (LAN models only) Configuration port

Figure 8. Front Panel Connectors (LAN Model Shown without the Decora Faceplate)

A

B

HDMI input connector — Connect a digital video source device to the HDMI connector. It can accept HDMI, DVI (with an appropriate adaptor), or dual mode DisplayPort video sources.

NOTES:

•The maximum HDMI cable length is 15 feet.

•Use an Extron LockIt lacing bracket to secure the HDMI connector to the device (see HDMI Connection on page 11).

Analog audio input connector — Connect an analog audio source to the 3.5 mm tip-ring-sleeve (TRS) jack.

Tip (L)

Ring (R)

Sleeve ()

Figure 9. Wiring a TRS Connector for Audio

By default, audio input is selected automatically (see Audio input selection SIS commands on page 20 to manually select audio inputs). When the HDMI input is selected with automatic audio input selections, the transmitter prioritizes embedded digital audio. The table on page 11 shows the audio format that is sent over the XTP connection when a specific audio format is not specified.

XTP T UWP 202 Wallplate Transmitter • Installation and Operation 10

Page 15 Page 17
Image 16
Page 15 Page 17
Contents XTP T UWP Safety Instructions FCC Class a Notice Registered TrademarksSpecifications Availability Software CommandsConventions Used in this Guide NotificationsContents XTP T UWP 202 Wallplate Transmitter Contents About this Guide IntroductionAbout the XTP T UWP Key Features Typical Point-to-Point Application Diagram LAN Model ShownXTP T UWP 202 Wallplate Transmitter Introduction Installation Operation Installation OverviewInstalling the Metal Junction Box or Mud Ring Cutting an Opening in the Mounting SurfaceInstalling the Mud Ring Installing the Mud Ring with Backing ClipsInstalling a UL Listed Metal Junction Box Rear and Side Panel ConnectorsXTP output connector RS-232 and IR Over XTP connector RS-232 IR Mounting the XTP T UWP XTP T UWPFront Panel Connectors Wiring a TRS Connector for AudioMaking Connections Hdmi ConnectionSelected Hdmi Embedded Analog Audio Audio Sent Over XTP Audio PresentSupported cables TP Cable Termination and RecommendationsCable recommendations Wiring the RS-232 and IR Over XTP Connector RS-232 and IR Over XTP CommunicationPower Connection Local powerPower injector Remote powerDirect power from an XTP matrix switcher Indicators OperationReset Modes Reset Mode Summary Mode Activation Result Purpose/NotesFactory Reset ModeSIS Configuration Control Host Device ConnectionSIS Programming Guide Host-to-Device and Device-to-Host CommunicationUsing the Command and Response Tables for SIS Commands Error ResponsesSymbol Definitions Input Commands Command and Response Tables for SIS CommandsAudio Configuration Commands Picture Adjustment Commands Analog Only Preset CommandsEdid Commands Advanced Configuration Commands Factory defaultsHdcp authorized device Hdmi input only Test patternXTP System Configuration Software Installing the XTP System Configuration SoftwareUsing the XTP System Configuration Software ConnectionsTop Menu File menuDisconnect ExitUpdate Firmware Confirm Disconnect Dialog BoxHelp menu About the SoftwareHelp Extron WebsiteDevice Settings AV Controls panelInput/Output tab Input/Output TabInput Presets panel Image Settings panelAnalog Video tab Audio tab Input format panelFactory reset Auto-input Switching panelGeneral tab Signal Information section Device Information panelGeneral Information section Audio Information sectionEdid Minder Assign EdidTo assign Edid to selected inputs To assign Edid to all inputsImport Edid Save output EdidSet favorite Edid Edid filtersUpdating Firmware with Firmware Loader Reference InformationDownloading Extron Firmware Loader Installing Firmware Loader Navigating to Firmware LoaderDownloading Firmware Downloading Firmware from the Extron WebsiteInstalling Firmware with Firmware Loader Add Device... Dialog BoxMounting Template Mounting Template for 2-gang Mud RingsExtron Warranty

XTP T UWP 202 specifications

The Extron XTP T UWP 202 is a state-of-the-art, two-gang wallplate transmitter designed for seamless integration into professional AV systems. As part of the XTP system by Extron, it leverages advanced technologies to ensure high-quality signal distribution over long distances, supporting both digital and analog video formats.

One of the standout features of the XTP T UWP 202 is its ability to transmit HDMI, along with audio and control signals, through a single CATx cable. This capability significantly simplifies installation and reduces cable clutter, making it an ideal choice for modern classrooms, conference rooms, and other professional environments. The wallplate connects directly to the XTP CrossPoint matrix switchers, allowing users to take advantage of centralized signal management.

The XTP T UWP 202 supports resolutions up to 4K@60Hz, covering a broad range of applications that require high-definition video output. The device is also equipped with EDID (Extended Display Identification Data) management, which guarantees optimal signal delivery by enabling automatic communication with the receiving display.

Another important aspect of the XTP T UWP 202 is its integrative capabilities. The wallplate includes a USB input for easy access to data sources, enhancing the overall connectivity of the AV system. Additionally, it supports Control Network, allowing integration with various control systems to manage connected devices effortlessly.

The design of the XTP T UWP 202 is user-friendly, featuring an intuitive layout that ensures ease of use for operators. The robust construction and sleek aesthetic allow it to blend seamlessly into any wall, while the included customizable labeling options help identify input sources clearly.

Moreover, the XTP T UWP 202 is equipped with anti-jitter technology, which helps to maintain signal integrity and reduces the chances of video artifacts, ensuring a reliable performance.

In summary, the Extron XTP T UWP 202 combines advanced transmission technology with high-definition video support and integrative features, making it a vital component for any professional AV installation. Its user-friendly design, combined with robust functionality, positions it as an excellent choice for users looking to optimize their AV experience.
Top Page Image Contents