Extron electronic XTP T UWP 202 manual Rear and Side Panel Connectors

Page 13

Installing a UL Listed Metal Junction Box

Metal junction boxes may differ slightly from model to model. Check with the manufacturer for specific installation instructions.

ATTENTION: Use metal junction boxes only.

Wall Stud

Screws or Nails

Wall opening is flush with edge of box.

Cable

Clamp

Signal Output

Cable

Figure 4. Installing a Metal Junction Box

1.Insert the metal junction box into the hole in the wall.

2.Secure it to the stud using two screws or nails, as appropriate. The front edge of the metal junction box must be flush with the front surface of the wall.

3.Feed cables through a metal junction box knockout opening.

4.Secure cables with clamps or ties to provide strain relief.

5.Trim back and insulate shields with heat shrink.

ATTENTION: To prevent short circuits, the outer foil shield can be cut back to the point where the cable exits the cable clamp. Both braided and foil shields should be connected to an equipment ground at the other end of the cable.

Rear and Side Panel Connectors

B CDA

Tx Rx G Tx Rx Tx Rx G

 

RS-232

IR

RS-232

POWER

 

 

 

12V

OVER XTP

REMOTE 1.0 A MAX.

 

 

XTP T UWP 202

 

 

 

XTP OUT

A

Rear

Side

A XTP output connector

C

B RS-232 and IR Over XTP connector

D

Figure 5. Rear Panel Connectors

Remote RS-232 connector DC power connector

XTP T UWP 202 Wallplate Transmitter • Installation and Operation

7

Page 12 Page 14
Image 13
Page 12 Page 14
Contents XTP T UWP Safety Instructions Registered Trademarks FCC Class a NoticeSoftware Commands Specifications AvailabilityConventions Used in this Guide NotificationsContents XTP T UWP 202 Wallplate Transmitter Contents About this Guide IntroductionAbout the XTP T UWP Typical Point-to-Point Application Diagram LAN Model Shown Key FeaturesXTP T UWP 202 Wallplate Transmitter Introduction Installation Overview Installation OperationCutting an Opening in the Mounting Surface Installing the Metal Junction Box or Mud RingInstalling the Mud Ring with Backing Clips Installing the Mud RingInstalling a UL Listed Metal Junction Box Rear and Side Panel ConnectorsXTP output connector RS-232 and IR Over XTP connector RS-232 IR XTP T UWP Mounting the XTP T UWPWiring a TRS Connector for Audio Front Panel ConnectorsHdmi Connection Making ConnectionsSelected Hdmi Embedded Analog Audio Audio Sent Over XTP Audio PresentSupported cables TP Cable Termination and RecommendationsCable recommendations RS-232 and IR Over XTP Communication Wiring the RS-232 and IR Over XTP ConnectorLocal power Power ConnectionPower injector Remote powerDirect power from an XTP matrix switcher Operation IndicatorsReset Mode Summary Mode Activation Result Purpose/Notes Reset ModesFactory Reset ModeHost Device Connection SIS Configuration ControlSIS Programming Guide Host-to-Device and Device-to-Host CommunicationUsing the Command and Response Tables for SIS Commands Error ResponsesSymbol Definitions Input Commands Command and Response Tables for SIS CommandsAudio Configuration Commands Preset Commands Picture Adjustment Commands Analog OnlyFactory defaults Edid Commands Advanced Configuration CommandsHdcp authorized device Hdmi input only Test patternInstalling the XTP System Configuration Software XTP System Configuration SoftwareConnections Using the XTP System Configuration SoftwareFile menu Top MenuDisconnect ExitConfirm Disconnect Dialog Box Update FirmwareAbout the Software Help menuHelp Extron WebsiteAV Controls panel Device SettingsInput/Output Tab Input/Output tabInput Presets panel Image Settings panelAnalog Video tab Input format panel Audio tabFactory reset Auto-input Switching panelGeneral tab Device Information panel Signal Information sectionGeneral Information section Audio Information sectionAssign Edid Edid MinderTo assign Edid to selected inputs To assign Edid to all inputsSave output Edid Import EdidSet favorite Edid Edid filtersUpdating Firmware with Firmware Loader Reference InformationDownloading Extron Firmware Loader Navigating to Firmware Loader Installing Firmware LoaderDownloading Firmware from the Extron Website Downloading FirmwareAdd Device... Dialog Box Installing Firmware with Firmware LoaderMounting Template for 2-gang Mud Rings Mounting TemplateExtron Warranty

XTP T UWP 202 specifications

The Extron XTP T UWP 202 is a state-of-the-art, two-gang wallplate transmitter designed for seamless integration into professional AV systems. As part of the XTP system by Extron, it leverages advanced technologies to ensure high-quality signal distribution over long distances, supporting both digital and analog video formats.

One of the standout features of the XTP T UWP 202 is its ability to transmit HDMI, along with audio and control signals, through a single CATx cable. This capability significantly simplifies installation and reduces cable clutter, making it an ideal choice for modern classrooms, conference rooms, and other professional environments. The wallplate connects directly to the XTP CrossPoint matrix switchers, allowing users to take advantage of centralized signal management.

The XTP T UWP 202 supports resolutions up to 4K@60Hz, covering a broad range of applications that require high-definition video output. The device is also equipped with EDID (Extended Display Identification Data) management, which guarantees optimal signal delivery by enabling automatic communication with the receiving display.

Another important aspect of the XTP T UWP 202 is its integrative capabilities. The wallplate includes a USB input for easy access to data sources, enhancing the overall connectivity of the AV system. Additionally, it supports Control Network, allowing integration with various control systems to manage connected devices effortlessly.

The design of the XTP T UWP 202 is user-friendly, featuring an intuitive layout that ensures ease of use for operators. The robust construction and sleek aesthetic allow it to blend seamlessly into any wall, while the included customizable labeling options help identify input sources clearly.

Moreover, the XTP T UWP 202 is equipped with anti-jitter technology, which helps to maintain signal integrity and reduces the chances of video artifacts, ensuring a reliable performance.

In summary, the Extron XTP T UWP 202 combines advanced transmission technology with high-definition video support and integrative features, making it a vital component for any professional AV installation. Its user-friendly design, combined with robust functionality, positions it as an excellent choice for users looking to optimize their AV experience.
Top Page Image Contents