Extron electronic XTP T UWP 202 manual SIS Configuration Control, Host Device Connection

Page 24

SIS Configuration and

Control

The XTP T UWP 202 can be configured and controlled using Extron Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see XTP System Configuration Software on page 23). This section contains basic SIS communication details and SIS commands and responses when connected directly to the XTP T UWP 202. Topics in this section include:

•Host Device Connection

•SIS Programming Guide

•Command and Response Tables for SIS Commands

Host Device Connection

Use a computer running the HyperTerminal or Extron DataViewer utility, or a control system to enable serial control of the transmitter. To connect directly to an XTP T UWP 202, connect the computer to the XTP T UWP 202 through the front panel USB Config port or the rear panel RS-232 connector. The protocol for the serial port is as follows: 9600 baud, no parity, 8 data bits, 1 stop bit, no flow control.

SIS Programming Guide

Host-to-Device and Device-to-Host Communication

SIS commands consist of one or more characters per field. No special characters are required to begin or end a command sequence. When the XTP T UWP 202 determines that a command is valid, it executes the command and sends a response to the host device. All responses from the switcher to the host end with a carriage return and a line feed

(CR/LF = ]), which signals the end of the response character string. A string is one or more characters.

Device-Initiated Message

When the transmitter is connected through the serial port only and a local event occurs, the device responds by sending a message to the host.

The following copyright messages are displayed after a power cycle via RS-232. The specific message displayed depends on the XTP T UWP 202 model.

NOTE: Black and white models are not differentiated in the displayed part number.

© Copyright YYYY, Extron Electronics XTP T UWP 202 Vx.xx, 60-1216-12]

© Copyright YYYY, Extron Electronics XTP T UWP 202 NL, Vx.xx, 60-1410-12]

YYYYis the year. Vx.xx is the firmware version number.

XTP T UWP 202 Wallplate Transmitter • SIS Configuration and Control 18

Page 23 Page 25
Image 24
Page 23 Page 25
Contents XTP T UWP Safety Instructions FCC Class a Notice Registered TrademarksSpecifications Availability Software CommandsConventions Used in this Guide NotificationsContents XTP T UWP 202 Wallplate Transmitter Contents Introduction About this GuideAbout the XTP T UWP Key Features Typical Point-to-Point Application Diagram LAN Model ShownXTP T UWP 202 Wallplate Transmitter Introduction Installation Operation Installation OverviewInstalling the Metal Junction Box or Mud Ring Cutting an Opening in the Mounting SurfaceInstalling the Mud Ring Installing the Mud Ring with Backing ClipsRear and Side Panel Connectors Installing a UL Listed Metal Junction BoxXTP output connector RS-232 and IR Over XTP connector RS-232 IR Mounting the XTP T UWP XTP T UWPFront Panel Connectors Wiring a TRS Connector for AudioMaking Connections Hdmi ConnectionSelected Hdmi Embedded Analog Audio Audio Sent Over XTP Audio PresentTP Cable Termination and Recommendations Supported cablesCable recommendations Wiring the RS-232 and IR Over XTP Connector RS-232 and IR Over XTP CommunicationPower Connection Local powerRemote power Power injectorDirect power from an XTP matrix switcher Indicators OperationReset Modes Reset Mode Summary Mode Activation Result Purpose/NotesFactory Reset ModeSIS Configuration Control Host Device ConnectionSIS Programming Guide Host-to-Device and Device-to-Host CommunicationError Responses Using the Command and Response Tables for SIS CommandsSymbol Definitions Command and Response Tables for SIS Commands Input CommandsAudio Configuration Commands Picture Adjustment Commands Analog Only Preset CommandsEdid Commands Advanced Configuration Commands Factory defaultsHdcp authorized device Hdmi input only Test patternXTP System Configuration Software Installing the XTP System Configuration SoftwareUsing the XTP System Configuration Software ConnectionsTop Menu File menuDisconnect ExitUpdate Firmware Confirm Disconnect Dialog BoxHelp menu About the SoftwareHelp Extron WebsiteDevice Settings AV Controls panelInput/Output tab Input/Output TabImage Settings panel Input Presets panelAnalog Video tab Audio tab Input format panelAuto-input Switching panel Factory resetGeneral tab Signal Information section Device Information panelGeneral Information section Audio Information sectionEdid Minder Assign EdidTo assign Edid to selected inputs To assign Edid to all inputsImport Edid Save output EdidSet favorite Edid Edid filtersReference Information Updating Firmware with Firmware LoaderDownloading Extron Firmware Loader Installing Firmware Loader Navigating to Firmware LoaderDownloading Firmware Downloading Firmware from the Extron WebsiteInstalling Firmware with Firmware Loader Add Device... Dialog BoxMounting Template Mounting Template for 2-gang Mud RingsExtron Warranty

XTP T UWP 202 specifications

The Extron XTP T UWP 202 is a state-of-the-art, two-gang wallplate transmitter designed for seamless integration into professional AV systems. As part of the XTP system by Extron, it leverages advanced technologies to ensure high-quality signal distribution over long distances, supporting both digital and analog video formats.

One of the standout features of the XTP T UWP 202 is its ability to transmit HDMI, along with audio and control signals, through a single CATx cable. This capability significantly simplifies installation and reduces cable clutter, making it an ideal choice for modern classrooms, conference rooms, and other professional environments. The wallplate connects directly to the XTP CrossPoint matrix switchers, allowing users to take advantage of centralized signal management.

The XTP T UWP 202 supports resolutions up to 4K@60Hz, covering a broad range of applications that require high-definition video output. The device is also equipped with EDID (Extended Display Identification Data) management, which guarantees optimal signal delivery by enabling automatic communication with the receiving display.

Another important aspect of the XTP T UWP 202 is its integrative capabilities. The wallplate includes a USB input for easy access to data sources, enhancing the overall connectivity of the AV system. Additionally, it supports Control Network, allowing integration with various control systems to manage connected devices effortlessly.

The design of the XTP T UWP 202 is user-friendly, featuring an intuitive layout that ensures ease of use for operators. The robust construction and sleek aesthetic allow it to blend seamlessly into any wall, while the included customizable labeling options help identify input sources clearly.

Moreover, the XTP T UWP 202 is equipped with anti-jitter technology, which helps to maintain signal integrity and reduces the chances of video artifacts, ensuring a reliable performance.

In summary, the Extron XTP T UWP 202 combines advanced transmission technology with high-definition video support and integrative features, making it a vital component for any professional AV installation. Its user-friendly design, combined with robust functionality, positions it as an excellent choice for users looking to optimize their AV experience.
Top Page Image Contents