Extron electronic SGS 408 manual Installation, cont’d, Cabling, Tabletop/desktop mounting

Page 14

Installation, cont’d

Tabletop/desktop mounting

For tabletop or desktop placement, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the enclosure.

Cabling

Up to eight input devices that produce component video, RGsB, RGBS, or RGBHV signals, can be connected to the switcher. The switcher can be connected to up to four output devices (two program and two preview) that accept RGBS or RGBHV signals, and, optionally, to one program output device that accepts DVI signals.

To cable the switcher, do the following:

1.Use BNC connectors to attach cables from the input devices to the switcher. Figure 2-3 shows the connection options.

R/R-Y	R/R-Y	R/R-Y	R/R-Y
G/Y	G/Y	G/Y	G/Y
B/B-Y	B/B-Y	B/B-Y	B/B-Y

Component	RGsB	RGBS	RGBHV
	(input only)

Figure 2-3 — Input connections

2.Use BNC connectors, 15-pin HD connectors, or a DVI connector to attach cables from the switcher to the output devices. Figure 2-4 shows the connection options.

15-pin HD

RGBS

RGBHV

DVI-D

Figure 2-4 — Output connections

Figure 2-5 shows a typical system installation and its cable connections.

See the next chapter, “Operation”, for information on configuring and using the switcher.

2-4 SGS 408 Switcher • Installation

Image 14

Contents Eight Input, High Resolution, Seamless Graphic Switcher SGSSicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad EspañolQuick Start SGS SGS 408 Quick Start QS-1Button Right adjustment knob Left adjustment knob Button Right adjustment knobLeft adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One Introductiontroduction, cont’d FeaturesSGS 408 Switcher Introduction About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Installation Installationstallation, cont’dRear Panel Connectors SGS 408 Switcher InstallationMounting the switcher Rack mountingTabletop/desktop mounting Installation, cont’dCabling Genlocking Video Inputs for Accu-RATE Frame Lock SGSAttaching an RCP Attaching an ECPXLR cable pinouts Pin SignalCable Pinouts DVI cable pinouts Making an RCP comm cableThree Front Panel Controls SGS 408 Switcher OperationOperationeration, cont’d Default Screen LCD default screenConfiguring the SGS Operation, cont’dSelecting the input configuration Selecting the input configuration menuSelecting the output rate Selecting the output sync format and polaritySelecting a test pattern Rgbs RgbhvChanging the title settings 12 Test patterns15 ECP control Setting the program keylock 18 Resetting the title box submenu controlsSetting the LCD appearance Performing a reset23 Performing a reset Sizing an image Using the Image ControlsCentering an image Adjusting contrast and brightness Filtering an imageSelecting an Input Freezing an inputApplying other effects Using the Black buttonApplying a cut Available effects32 Standard wipe transitions 35 Square wipe effects Setting up a new effect 37 ECP key title effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect 44 Setting up the Square wipe effect Implementing an established effectUsing executive mode Implementing a titleOptimizing the Image Four RS-232 Programmer’s Guide SGS 408 Switcher Serial CommunicationSerialCommunicationunication, c t’d SGS-initiated messagesSGS error responses Using the command/response tableCommand/response table Serial Communication, cont’dCommand Ascii Response Description Command Ascii Advanced Instructions Installing the softwareControl Software for Windows Using the software SGS 408 Control Program windowFive SGS 408 Switcher Troubleshooting Troubleshootingubleshooting, cont’dIf the switcher does not respond to controls If the image does not appearAAppendix a Specificationsecifications, cont’d SGS 408 Switcher SpecificationsGeneral Specifications, cont’d AppendixBB Installing the DVI connector option Upgrades and RepairsInternal access SGS 408 Switcher Reference InformationFigure B-2 Installing the DVI connector option Replacing the AC fuseInstalling a firmware update Reference Information, cont’dFigure B-4 Locating and replacing ICs Extron Part Part Number Part NumbersRelated part numbers FCC Class a Notice Extron’s Warranty Extron Electronics, USA