Extron electronic SGS 408 manual Cable Pinouts, XLR cable pinouts, Pin Signal

Page 17

Projectors

SGS 408	SGS 408

		SGS 408
	Program	Program
	Program	Monitor
	Monitor	Monitor
	Monitor	Preview
	Preview	Preview
	Preview	Monitor
	Monitor	Monitor
	Monitor	Program
		Program
		Monitor
	ECP 1000	Preview
	Up to 50'	Monitor
		Control Room

RCP 1000

Figure 2-8 — SGS 408 and ECP 1000

Cable Pinouts

XLR cable pinouts

The XLR connector (figure 2-9) uses the following pinouts:

Pin	Signal	Pin	Signal
1	+12 V	3	Communications line
2	Not used	4	Ground

41

3 2

Figure 2-9 — XLR connector

SGS 408 Switcher • Installation

2-7

Image 17

Contents SGS Eight Input, High Resolution, Seamless Graphic SwitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolSGS 408 Quick Start QS-1 Quick Start SGSLeft adjustment knob Button Right adjustment knobButton Right adjustment knob Left adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One SGS 408 Switcher Introduction FeaturesIntroductiontroduction, cont’d About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Rear Panel Connectors Installationstallation, cont’dInstallation SGS 408 Switcher InstallationRack mounting Mounting the switcherTabletop/desktop mounting Installation, cont’dCabling SGS Genlocking Video Inputs for Accu-RATE Frame LockAttaching an ECP Attaching an RCPXLR cable pinouts Pin SignalCable Pinouts Making an RCP comm cable DVI cable pinoutsThree Front Panel Controls SGS 408 Switcher OperationOperationeration, cont’d LCD default screen Default ScreenOperation, cont’d Configuring the SGSSelecting the input configuration menu Selecting the input configurationSelecting the output sync format and polarity Selecting the output rateRgbs Rgbhv Selecting a test pattern12 Test patterns Changing the title settings15 ECP control 18 Resetting the title box submenu controls Setting the program keylockPerforming a reset Setting the LCD appearance23 Performing a reset Sizing an image Using the Image ControlsCentering an image Filtering an image Adjusting contrast and brightnessFreezing an input Selecting an InputApplying a cut Using the Black buttonApplying other effects Available effects32 Standard wipe transitions 35 Square wipe effects 37 ECP key title effect Setting up a new effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect Implementing an established effect 44 Setting up the Square wipe effectImplementing a title Using executive modeOptimizing the Image Four SerialCommunicationunication, c t’d SGS 408 Switcher Serial CommunicationRS-232 Programmer’s Guide SGS-initiated messagesUsing the command/response table SGS error responsesSerial Communication, cont’d Command/response tableCommand Ascii Response Description Command Ascii Advanced Instructions Installing the softwareControl Software for Windows SGS 408 Control Program window Using the softwareFive If the switcher does not respond to controls Troubleshootingubleshooting, cont’dSGS 408 Switcher Troubleshooting If the image does not appearAAppendix a SGS 408 Switcher Specifications Specificationsecifications, cont’dGeneral Specifications, cont’d AppendixBB Internal access Upgrades and RepairsInstalling the DVI connector option SGS 408 Switcher Reference InformationReplacing the AC fuse Figure B-2 Installing the DVI connector optionReference Information, cont’d Installing a firmware updateFigure B-4 Locating and replacing ICs Extron Part Part Number Part NumbersRelated part numbers FCC Class a Notice Extron’s Warranty Extron Electronics, USA