Extron electronic manual Quick Start SGS 408, cont’d, Button Right adjustment knob

Page 4

Quick Start — SGS 408, cont’d

Adjusting an Image

From the default screen, press the indicated button. To adjust the preview image, press the button again.

Button

Right adjustment knob

Center

Move image horizontally

Size

Adjust image width

Filter

Select horizontal filter

Level

Adjust image brightness

Left adjustment knob

Move image vertically Adjust image height Select vertical filter Adjust image contrast

Configuring the Switcher

 

From the default screen, press the Menu button.

 

 

 

Button

Right adjustment knob

Left adjustment knob

 

 

 

 

 

Next — Press to display the next “page “ of configuration options.

 

 

 

Input Config

Select input to be configured.

Select video format.

 

 

Out Rate

Select resolution.

Select refresh rate or lock*.

 

 

Out Sync

Select output sync format.

Select output sync polarity.

 

 

Test Pattern

Select output device.

Select test pattern.

 

 

Exit — Press to exit the menu and return to default screen.

 

 

 

Edit Title — Press to display the title box options.

 

 

 

Prog Lock

Turn program keylock on/off.

N/A

 

LCD

Adjust LCD screen contrast.

Adjust LCD screen brightness.

 

Reset — Press to select reset of program, preview, program and preview, or system.

 

Edit Title (press ECP) — Press to toggle between title window or key effect.

 

Edit Title (press Center)

Adjust horizontal shift.

Adjust vertical shift.

 

Edit Title (press Size)

Adjust title box width.

Adjust title box height.

Edit Title (press reset) — Press Reset button to return title box to its original size and location. System Reset — Press button again to reset all settings to their factory defaults.

* The output frame rate is locked to the frame rate of input #1.

Applying a Cut

1.Press the preview input button that corresponds to the input that you want to switch to.

2.Press the Cut button.

Setting Up an Effect

1.Press the Effect button that you want to program.

2.Turn the right adjustment knob until the name of the effect appears on the LCD.

3.Turn the left adjustment knob until the desired duration appears.

4.If the effect is a dissolve or title, press the Take button. If the effect is a standard, curtain, plus, or square wipe, press the desired transition button.

Applying an Effect

1.Press the preview input button that corresponds to the input that you want to switch to.

2.Press the Effect button for the desired effect. (If it is already lit, you do not need to press it.)

3.Verify that the selected effect and transition, as displayed in the upper right corner of the LCD screen, are correct.

4.If desired, override the duration by turning the left adjustment knob.

5.When you want the effect to occur, press the Take button.

6.If you are applying a title, when you want the title to end, press the Take button again.

QS-2 SGS 408 • Quick Start

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Eight Input, High Resolution, Seamless Graphic Switcher SGSSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start SGS SGS 408 Quick Start QS-1Button Right adjustment knob Left adjustment knobButton Right adjustment knob Left adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One Features SGS 408 Switcher IntroductionIntroductiontroduction, cont’d About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Rear Panel ConnectorsInstallation SGS 408 Switcher InstallationMounting the switcher Rack mountingCabling Installation, cont’dTabletop/desktop mounting Genlocking Video Inputs for Accu-RATE Frame Lock SGSAttaching an RCP Attaching an ECPCable Pinouts Pin SignalXLR cable pinouts DVI cable pinouts Making an RCP comm cableThree Operationeration, cont’d SGS 408 Switcher OperationFront Panel Controls Default Screen LCD default screenConfiguring the SGS Operation, cont’dSelecting the input configuration Selecting the input configuration menuSelecting the output rate Selecting the output sync format and polaritySelecting a test pattern Rgbs RgbhvChanging the title settings 12 Test patterns15 ECP control Setting the program keylock 18 Resetting the title box submenu controlsSetting the LCD appearance Performing a reset23 Performing a reset Centering an image Using the Image ControlsSizing an image Adjusting contrast and brightness Filtering an imageSelecting an Input Freezing an inputUsing the Black button Applying a cutApplying other effects Available effects32 Standard wipe transitions 35 Square wipe effects Setting up a new effect 37 ECP key title effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect 44 Setting up the Square wipe effect Implementing an established effectUsing executive mode Implementing a titleOptimizing the Image Four SGS 408 Switcher Serial Communication SerialCommunicationunication, c t’dRS-232 Programmer’s Guide SGS-initiated messagesSGS error responses Using the command/response tableCommand/response table Serial Communication, cont’dCommand Ascii Response Description Command Ascii Control Software for Windows Installing the softwareAdvanced Instructions Using the software SGS 408 Control Program windowFive Troubleshootingubleshooting, cont’d If the switcher does not respond to controlsSGS 408 Switcher Troubleshooting If the image does not appearAAppendix a Specificationsecifications, cont’d SGS 408 Switcher SpecificationsGeneral Specifications, cont’d AppendixBB Upgrades and Repairs Internal accessInstalling the DVI connector option SGS 408 Switcher Reference InformationFigure B-2 Installing the DVI connector option Replacing the AC fuseInstalling a firmware update Reference Information, cont’dFigure B-4 Locating and replacing ICs Related part numbers Part NumbersExtron Part Part Number FCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents