Extron electronic SGS 408 manual Square wipe effects

Page 36

Operation, cont’d

•A square wipe causes the preview image to appear to unroll over the program image in one of two transitions (figure 3-35):

•Starting at all four edges of the screen and moving in to the center of the screen.

•Starting at the center of the screen and moving out to the edges of the screen.

Figure 3-35 — Square wipe effects

• A title effect produces two different effects: ECP window and ECP key.

ECP window causes a predefined box in the program image to dissolve to reveal the preview image (figure 3-36). The effect is as if the preview image were located behind the program image, and a window in the program image opens to show the preview image. When the effect ends, the preview image disappears, and the program image is again intact (see “Changing the title settings” on page 3-8 for information on defining the title box).

Preview	Program

Program

During Window Effect

Figure 3-36 — ECP window title effect

3-18 SGS 408 Switcher • Operation

Image 36

Contents Eight Input, High Resolution, Seamless Graphic Switcher SGSSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start SGS SGS 408 Quick Start QS-1Button Right adjustment knob Left adjustment knobButton Right adjustment knob Left adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One Features SGS 408 Switcher IntroductionIntroductiontroduction, cont’d About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Rear Panel ConnectorsInstallation SGS 408 Switcher InstallationMounting the switcher Rack mountingInstallation, cont’d CablingTabletop/desktop mounting Genlocking Video Inputs for Accu-RATE Frame Lock SGSAttaching an RCP Attaching an ECPPin Signal Cable PinoutsXLR cable pinouts DVI cable pinouts Making an RCP comm cableThree SGS 408 Switcher Operation Operationeration, cont’dFront Panel Controls Default Screen LCD default screenConfiguring the SGS Operation, cont’dSelecting the input configuration Selecting the input configuration menuSelecting the output rate Selecting the output sync format and polaritySelecting a test pattern Rgbs RgbhvChanging the title settings 12 Test patterns15 ECP control Setting the program keylock 18 Resetting the title box submenu controlsSetting the LCD appearance Performing a reset23 Performing a reset Using the Image Controls Centering an imageSizing an image Adjusting contrast and brightness Filtering an imageSelecting an Input Freezing an inputUsing the Black button Applying a cutApplying other effects Available effects32 Standard wipe transitions 35 Square wipe effects Setting up a new effect 37 ECP key title effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect 44 Setting up the Square wipe effect Implementing an established effectUsing executive mode Implementing a titleOptimizing the Image Four SGS 408 Switcher Serial Communication SerialCommunicationunication, c t’dRS-232 Programmer’s Guide SGS-initiated messagesSGS error responses Using the command/response tableCommand/response table Serial Communication, cont’dCommand Ascii Response Description Command Ascii Installing the software Control Software for WindowsAdvanced Instructions Using the software SGS 408 Control Program windowFive Troubleshootingubleshooting, cont’d If the switcher does not respond to controlsSGS 408 Switcher Troubleshooting If the image does not appearAAppendix a Specificationsecifications, cont’d SGS 408 Switcher SpecificationsGeneral Specifications, cont’d AppendixBB Upgrades and Repairs Internal accessInstalling the DVI connector option SGS 408 Switcher Reference InformationFigure B-2 Installing the DVI connector option Replacing the AC fuseInstalling a firmware update Reference Information, cont’dFigure B-4 Locating and replacing ICs Part Numbers Related part numbersExtron Part Part Number FCC Class a Notice Extron’s Warranty Extron Electronics, USA