Extron electronic SGS 408 manual SGS error responses, Using the command/response table

Page 45

SGS error responses

When the switcher receives an SIS command and determines that it is valid, it performs the command and sends a response to the host device. If the switcher is unable to perform the command because the command is invalid or contains invalid parameters, the switcher returns an error response to the host. The error response codes are:

E01 — Invalid input number (too large)

E10 — Invalid command

E11 — Invalid preset

E12 — Invalid output number (too large)

E13 — Invalid value (out of range)

E23 — Checksum error

Using the command/response table

The command/response table begins on the next page. Lower case letters are acceptable in the command field only where indicated. Symbols are used throughout the table to represent variables in the command/response fields. Symbol definitions are shown at the beginning of the response table, as is an ASCII-to-hexadecimal conversion table. Command and response examples are shown throughout the table.

SGS 408 Switcher • Serial Communication

4-3

Image 45

Contents SGS Eight Input, High Resolution, Seamless Graphic SwitcherConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolSGS 408 Quick Start QS-1 Quick Start SGSLeft adjustment knob Button Right adjustment knobButton Right adjustment knob Left adjustment knob Quick Start SGS 408, cont’dTable of Contents Table of Contents, cont’d One SGS 408 Switcher Introduction FeaturesIntroductiontroduction, cont’d About the SGSSGS 408 Switcher Introduction Introduction, cont’d Two Rear Panel Connectors Installationstallation, cont’dInstallation SGS 408 Switcher InstallationRack mounting Mounting the switcherInstallation, cont’d CablingTabletop/desktop mounting SGS Genlocking Video Inputs for Accu-RATE Frame LockAttaching an ECP Attaching an RCPPin Signal Cable PinoutsXLR cable pinouts Making an RCP comm cable DVI cable pinoutsThree SGS 408 Switcher Operation Operationeration, cont’dFront Panel Controls LCD default screen Default ScreenOperation, cont’d Configuring the SGSSelecting the input configuration menu Selecting the input configurationSelecting the output sync format and polarity Selecting the output rateRgbs Rgbhv Selecting a test pattern12 Test patterns Changing the title settings15 ECP control 18 Resetting the title box submenu controls Setting the program keylockPerforming a reset Setting the LCD appearance23 Performing a reset Using the Image Controls Centering an imageSizing an image Filtering an image Adjusting contrast and brightnessFreezing an input Selecting an InputApplying a cut Using the Black buttonApplying other effects Available effects32 Standard wipe transitions 35 Square wipe effects 37 ECP key title effect Setting up a new effect38 Setting up the Dissolve effect 41 Setting up the S curtains effect Implementing an established effect 44 Setting up the Square wipe effectImplementing a title Using executive modeOptimizing the Image Four SerialCommunicationunication, c t’d SGS 408 Switcher Serial CommunicationRS-232 Programmer’s Guide SGS-initiated messagesUsing the command/response table SGS error responsesSerial Communication, cont’d Command/response tableCommand Ascii Response Description Command Ascii Installing the software Control Software for WindowsAdvanced Instructions SGS 408 Control Program window Using the softwareFive If the switcher does not respond to controls Troubleshootingubleshooting, cont’dSGS 408 Switcher Troubleshooting If the image does not appearAAppendix a SGS 408 Switcher Specifications Specificationsecifications, cont’dGeneral Specifications, cont’d AppendixBB Internal access Upgrades and RepairsInstalling the DVI connector option SGS 408 Switcher Reference InformationReplacing the AC fuse Figure B-2 Installing the DVI connector optionReference Information, cont’d Installing a firmware updateFigure B-4 Locating and replacing ICs Part Numbers Related part numbersExtron Part Part Number FCC Class a Notice Extron’s Warranty Extron Electronics, USA